Anti Rattle Device for Use with Equal-i-zer Weight Distribution

Question

Question:

what do you recommend for an anti rattle hitch pin to be used with a solid shank Equalizer Hitch. And the receiver only has one hole ?

asked by: Doug B

0

Expert Reply:

You could use a U-bolt style of anti-rattle device with your solid shank Equal-i-zer weight distribution like the part # e99007. Most of the other kinds of anti-rattle devices require the shank to be hollow which is why the # 63201 that you referenced would not work.

expert reply by: Jameson C

0

Answer 1

The Malone Anti-Rattle HitchLock System part #MPG908 will help hold the shank of the weight distribution system inside the receiver tube more securely. Therefore, you won't have as much side to side or front to back movement with the shank…

view full answer...

Answer 2

The Roadmaster Quiet Hitch #RM-061 referenced in your question does not have a specific weight capacity. Because it will not be supporting really any weight during towing, there simply isn't a listed weight limit. With that being said, the unit…

view full answer...

Answer 3

The Brophy Stabilizer Clamp and U-Bolt for 2" Hitch Receiver #RSCP holds the ball mount up against one surface of the receiver opening. The location as the top or bottom does not effect function. The u-bolt will be able to handle the weight in…

view full answer...

Answer 4

As you've discovered, a 2 inch receiver doesn't always measure exactly two inches by two inches. There is a manufacturing tolerance involved that allows the receiver to be a few hundredths of an inches larger or smaller than 2 inches, but…

view full answer...

Answer 5

There are several anti-rattle devices that would be good to use when towing. The construction of your ball mount will determine the best choice for your application. If your ball mount is hollow, and you have a 2-inch receiver hitch, then I would…

view full answer...

Answer 6

An E3 code on a Furrion Chill Replacement RV Air Conditioner for Dometic Brisk Setup - 15,000 Btu #FR42PV means a loss of communication between the thermostat and control box. Check to make sure your wires have no kinks or damage and are making a…

view full answer...

Answer 7

I have two favorites when it comes to anti-rattle devices. The first is the Roadmaster Quiet Hitch for 2" Trailer Hitches part #RM-061 the other is the Curt Anti-Rattle Kit for 2" Trailer Hitches part #C22321. The Blue Ox Part #BX88312 is…

view full answer...

Answer 8

Yes. You can use the Malone Anti-Rattle Hitch Lock System #MPG908 to help reduce/eliminate rattle between your receiver and ball mount when towing your travel trailer. With that said, my preferred solution for this is the Roadmaster Quiet Hitch…

view full answer...

Answer 9

The Roadmaster Quiet Hitch #RM-061 that you referenced (and many similar items) are intended for use only when flat-towing a vehicle, but are not suitable for use with a trailer. One option that you can try is the Malone #MPG908 Anti-Rattle system.…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Anti Rattle Device for Use with Equal-i-zer Weight Distribution

Products Referenced in This Question

Featured Help Information

Instructions

Continue Researching