How to Determine if Redline Single-Axle Trailer Fender Fits Shorelander Trailer

Question

Question:

Will this fit a 14 foot shorlander trailer ?

asked by: Justin K

0

Expert Reply:

These replacement trailer fenders are not designed to fit any specific trailer, so there wouldn't be any way to know with certainty what fenders are a fit for your Shorelander trailer. That said, there is a pretty easy way to determine the fit. All you need to do is know the size of the wheels on your trailer, and then measure your fenders.

If your trailer has wheels that are 13" to 15" and your current fender have a similar 11-5/16" width and 45" length (or 32-3/4" length if your trailer does not have steps) then yes, you can use the Redline fenders, and will also need the mounting brackets if you don't have them:

- Plastic, Single-Axle Trailer Fender with Top and Side Steps # PF11X35W

- Galvanized Steel, U-Shaped, Bolt-On Brackets # PF1135-BKT-2

I have added links below to a video review for you to check out as well if you'd like to take a look.

expert reply by: Kyle S

0

Answer 1

I was able to go out to the warehouse and measure the mounting brackets holes for the PF11X35W and found that it was 5-5/16 inches or 5.3125 inches. If these aren't an exact match, new holes can usually be drilled into the brackets to make…

view full answer...

Answer 2

We have heard from previous customers that the Fulton replacement fenders part #F008573 that you referenced will fit and replace fenders on a Shorelandr trailer like what you have.

view full answer...

Answer 3

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 6

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 7

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...

Answer 8

Your math is correct in your trailer weight load example. If a fully-loaded tandem axle trailer weighs 4000-lbs then each of the 4 tires will bear 1/4th of that load, or 1000-lbs. In this case a tire rated for 1300-lbs would provide a good safety…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

You can add larger wheels and tires to a trailer as long as you have enough room for the larger size. The main clearance issues we find when putting larger tires and wheels on a trailer is from the top of the tire to the fender and from the inside…

view full answer...

Answer 11

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 12

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

How to Determine if Redline Single-Axle Trailer Fender Fits Shorelander Trailer

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching