Motor RPM and Torque For Lippert LC368200 Motor & Gear Assembly

Question

Question:

Just trying to find out the rpm and torque for the lc368200 motor

asked by: Ryan

0

Expert Reply:

I reached out to my contact at Lippert Technical Support regarding the Lippert # LC368200 Motor & Gear Assembly, and found that the RPM and torque for this motor is not published. Also, the motor is not sold separately. They were able to tell me that this was 12 volts and was geared 1:163. I am sorry that I could not provide more information.

expert reply by: Les D

0

Answer 1

The part number on your Power Gear Slide-Out motor is actually 524908, for which the correct replacement is part #LC368200. I was able to confirm this with Lippert.

view full answer...

Answer 2

The Replacement Gear Motor Assembly for Lippert Component Power Gear Slide Out part #LC67FR has a limited one year warranty as with all of their slide-out motors which will protect you from any manufacturing defects.

view full answer...

Answer 3

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 4

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5 inches…

view full answer...

Answer 5

My contact at Yates Rubber advises that a nominal 8-inch keel roller does not measure exactly 8 inches; typically they are slightly smaller than the specified size, much the way a piece of 2 x 4 lumber is not exactly 2-inches by 4-inches. I took…

view full answer...

Answer 6

By "mobile home type bolt pattern" I believe you are talking about a 5 spoke utility bolt pattern such as what is on the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles #8-174-5UC3. To measure your axle from hub face to…

view full answer...

Answer 7

We do offer the Trailer Connector Adapter, #HM47425, which converts a 7-pole round connector to a 7-pole flat connector. This adapter works for tow vehicles with combined taillight wiring, meaning that the turn signals and brake lights run on the…

view full answer...

Answer 8

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 9

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 10

According to Solara (Lippert), the correct number of turns to set the proper tension of their slide toppers like #LCV000163285 is between 12 to 16 turns, so I'd consider 14 to be a pretty good happy medium.

view full answer...

Answer 11

I do have an option but Glo-Brite is no longer in business so you won't be able to get any replacement parts for these lights such as lenses. The only option you have would be a full replacement for which the most similar option we offer is the…

view full answer...

Answer 12

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Motor RPM and Torque For Lippert LC368200 Motor & Gear Assembly

Product Page this Question was Asked From

Continue Researching