Heating Element & Location For Atwood GC6AA-10E

Question

Question:

Atwood water heater gc6aa-10e location of the heating element. Can’t fined heating element and electric won’t heat tank

asked by: John

0

Expert Reply:

Take a look at the accompanying diagram I added for you, and you can see where the heating element is on your Atwood water heater GC6AA-10E; it is number 17 in the diagram and on the back of the unit, so the heater will need to be removed to do the repair, which should only be done by a qualified professional due to the inherent dangers.

The correct replacement element and tool are the following:

- Camco Water Heater Element # CAM02103

- Camco Wrench for Screw-In Water Heater Element # CAM09883

I have added a link below to a video review for you to check out as well if you'd like to take a look.

expert reply by: Kyle S

0

Heating Element Location
(click to enlarge)

Answer 1

Yes, you do have a bad motor assembly and based on the numbers you said you found the correct replacement motor is the part #LC379147 that you referenced.

view full answer...

Answer 2

The proper replacement heating element for your Dometic GC6AA-10E is the Camco #CAM02103. Because the element is accessed from the rear of the unit, Dometic recommends having a qualified service center complete the installation. A specific socket…

view full answer...

Answer 3

The removal of the hot water heater element can be difficult. You can use a crescent wrench on the hex head of the element to unscrew it but Camco has a special wrench #CAM09883 to help with removing that element. This allows you to use a…

view full answer...

Answer 4

The heating element on your Atwood model GC10A-4E water heater (our part #AT94022) should be on the backside of the unit, towards the bottom of the tank. It will actually be behind the gas line assembly, which will need to be loosened and moved out…

view full answer...

Answer 5

It sounds like you have a lack of LP flow, check to see if the pilot light itself is lit; it should be. If your propane supply is good, full bottles and a functioning regulator, verify this by operation check of another LP appliance such as the…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 9

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 10

The best hitch for your 2023 Honda Passport is going to be the Curt Hitch item #C13421. This hitch is custom fit and bolts to your Honda with included hardware. I really like the Curt hitch because it tucks up underneath your rear bumper cover nicely…

view full answer...

Answer 11

To add a class III hitch to your 2024 Honda CR-V hybrid, I recommend the Curt Trailer Hitch item #C13397. This hitch is custom fit and bolts to your CR-V with included hardware. It is a class III hitch with a 2" receiver. I really like this…

view full answer...

Answer 12

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Heating Element & Location For Atwood GC6AA-10E

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching