What is the Length of the Arched Loading Ramp Set Folded and Unfolded?

Question

Question:

Can I please the folded height of the ramps. So the height off the ground when folded and laying flat on ground. I want to slide under my golf cart once loaded and have adequate clearance. Thanks

asked by: John

0

Expert Reply:

I confirmed with Stallion that the thickness of the Arched Loading Ramp Set - Center Fold - Aluminum # 288-07432-2 when stacked on top of each other is 6 inches when folded at the center.

expert reply by: Bob C

0

Answer 1

I have a solution for you.The main concern I would warn you about in this scenario is that if the weight that is either distributed on the ground or on the trailer exceeds 1500 pounds for even a brief instant, it could not just potentially damage…

view full answer...

Answer 2

I really like the Arched Loading Ramp Set #288-07432-2 because they are a little longer at 90", they have a wider 18" base than standard ramps, they are made of aluminum so you don't have to worry about rust, and they fold…

view full answer...

Answer 3

There is a potential solution for you but the Arched Loading Ramp Set #288-07432-2 you referenced would not work with your 2017 GMC Sierra 2500HD with a 39-1/2 inch bed height. Instead, you may be able to use the Erickson Arched, Aluminum Loading…

view full answer...

Answer 4

The CargoSmart Loading Ramp #3483075 is rated for a maximum weight of 1500lbs when the weight is evenly distributed. Each side would carry 750lbs. If your golf cart is 970lbs without anyone on it that would be 485lbs per side. The drivers weight…

view full answer...

Answer 5

Yes, a single arched loading ramp is part #288-07432. Please keep in mind the weight rating of a single ramp is 1,500 lbs compared to 3,000 lbs for the set. The set is part #288-07432-2. I have attached a video for your reference.

view full answer...

Answer 6

I had the Stallion ATV Ramps #288-07432-2 measured and the spaces are 2 3/4 by 4 3/4. I included a picture of how they were measured as well. The red is 4 3/4 inches and the blue is 2 3/4 inches.

view full answer...

Answer 7

The longest folding ramps we have for you is the Arched Loading Ramp Set part #288-07432 for 1 or part #288-07432-2 for 2 which are 90" long. The 90" length will ensure the angle that will be required to load the generator in your truck bed…

view full answer...

Answer 8

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 9

The spring hanger placement is going to be determined by your axle spacing. For example, if your axles are spaced 33 inches apart, as shown in the attached diagram, a 7K axle slipper spring, like #e74SR, requires a distance of 28-1/2 inches between…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

What is the Length of the Arched Loading Ramp Set Folded and Unfolded?

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching