Roof Rack Cross Bars

Question

Question:

I am looking for the lowest profile possible for a 2009 F250 Super Duty cab cross bars so I can mount a roof cargo basket. . Can you point me in the right direction.

asked by: Daryl P

0

Expert Reply:

The Rhino-Rack ROC25 Roof Rack for Naked Roofs - Vortex Aero Crossbars # RR22YR will be a nice low-profile roof rack for your 2009 F250 if it is a Super Cab. If you have Crew Cab then the correct version of this roof rack is # RR54SR. If you happen to have Regular Cab then you cannot fit a cargo rack on your roof and you are limited to a truck bed rack such as Yakima BedRock HD Truck Bed Rack - Aluminum - 300 lbs - 78" Crossbars # Y01160-59.

There are many roof baskets that will work for the crossbar setups mentioned above; the Rhino-Rack Roof Mounted Steel Cargo Basket - 47" Long x 35" Wide - 165 lbs # RMCB would be a nice economical option. I attached demonstration videos for you to check out.

expert reply by: Andrew N

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 3

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 7

It will indeed work; I just checked with Lippert for you and was able to verify the correct toggle switch for your Lippert Power Stance Electric Trailer Jack #LC69VR (which is the 813748), is the following: - Replacement Extend/Retract Switch for…

view full answer...

Answer 8

The spring hanger placement is going to be determined by your axle spacing. For example, if your axles are spaced 33 inches apart, as shown in the attached diagram, a 7K axle slipper spring, like #e74SR, requires a distance of 28-1/2 inches between…

view full answer...

Answer 9

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 10

Hey Alex, it sounds like you are looking for just the tracks of the Rhino Rack camper shell roof rack kit #Y02-480B which we do offer with the part #RTC16.

view full answer...

Answer 11

Hi H.L. There isn't actually a specific weight capacity for any 5th wheel base rail kit, including the B&W Custom Installation Kit w/ Base Rails #BWRVK2401 that fits your 2016 Ford F-250. Base rails are designed to meet the tow capacity of…

view full answer...