Which Brake Controller Adapter for 2017 Nissan Pathfinder with Hayes Synchronizer

Question

Question:

i have the hayes model #812725 syncronizer brake controller and want to install it on my nissan pathfinder 2017. I found the connector but need cagle to connect from the car to the above syncronizer. What cable do you have that will do the job? thanks for your help you are great to work with!

asked by: JIm E

0

Expert Reply:

You can use a Hayes Synchronizer # HA81725 in your 2017 Nissan Pathfinder using the plug and play adapter Custom Wiring Adapter for Hayes Brake Controllers - Dual Plug # HA81786-HBC. This will be the plug that goes from the car to the controller.

expert reply by: Erik B

0

Answer 1

I am not sure which Hayes brake controller that you have, but in reviewing the installation instructions for the Hayes-Lemmerz Energize III+ Electric Trailer Brake Controller #HA81742B I found that there is a section that goes over if the…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The first thing you will need for your 1999 D250 is a 4-way. The Curt T-Connector Vehicle Wiring Harness #C55317 plugs into the connection points behind your rear bumper and will allow you to power your trailer's signal lights. Once the 4-way is…

view full answer...

Answer 7

If you have a vehicle specific wiring harness for a brake controller then that would indicate that you have a factory tow package and subsequently would already have a 7-way at the back of your vehicle. The universal 7-way connector #ETBC7 is meant…

view full answer...

Answer 8

There is a trailer hitch receiver as well as a 4-way wiring harness that fit your 2022 Jeep Grand Cherokee WL; that said, we don't have any way to reference a VIN so you'll need to confirm if you do have the WL, which is the new model of…

view full answer...

Answer 9

Hey Antoine, so the two kits you mentioned are actually really similar and honestly I would go with the part #ETBC7 if I were you. The #ETBC7L is basically the same thing minus a couple wires and breakers so you may as well get the kit that has…

view full answer...

Answer 10

For your 2024 Hyunda Santa Cruz we have the Curt 7-way kit part #C68JR that is a confirmed fit. This installs by plugging into a factory wiring connector on your vehicle which means a really easy install that doesn't require any splicing.

view full answer...

Answer 11

The best brake controller for your 2024 Toyota Grand Highlander is from Redarc, and the correct part number for it and the needed wiring adapter is the following: - Redarc Tow-Pro Liberty Trailer Brake Controller #RED24FR - Wiring Adapter for Tow-Pro…

view full answer...

Answer 12

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...