Does Wheel for AM3S638 Have Adjacent Wheel Bolt Holes 3 Inches Apart On Center

Question

Question:

I need to know if the Dinch measurement in the diagram is 3.

asked by: William A

0

Expert Reply:

The # AM3S638 Kenda Loadstar ST205/75D15 Bias Trailer Tire with 15" White Wheel has a 5 on 5 bolt pattern. The 5 on 5 bolt pattern would have adjacent bolt holes that are 3 inches apart, measured center to center which is indeed the 'D' measurement in the photo you provided.

I've linked to product videos for the # AM3S638 wheel/tire combo you'd looked at.

expert reply by: Mike L

0

Customer Submitted Photo
(click to enlarge)

Answer 1

Yes, about 99 percent of A-frame jacks use the same mounting pattern. The holes are generally 3 inches apart on center though it can vary ever so slightly which is why some jacks have slotted holes.

view full answer...

Answer 2

The exterior lights on your trailer - stop, turn and tail - and the interior lights will usually be fed by different power sources. On an RV-style 7-way the stop/turn light signals are carried on the pins at the 3-o-clock and 9-o-clock positions…

view full answer...

Answer 3

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 6

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 7

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 8

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 9

Brake systems are not dependent on the hub bolt pattern. So you can use the Electric Trailer Brake Kit #AKEBRK-7-SA for 12 inch hub/drums or #AKEBRK-35-SA for 10 inch hub/drums. Then use #10-1-1 wire sold by the foot for your brake magnet wiring.…

view full answer...

Answer 10

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Answer 11

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 12

By "mobile home type bolt pattern" I believe you are talking about a 5 spoke utility bolt pattern such as what is on the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles #8-174-5UC3. To measure your axle from hub face to…

view full answer...

Does Wheel for AM3S638 Have Adjacent Wheel Bolt Holes 3 Inches Apart On Center

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching