Peterson Round Trailer Tail Light Wire Connections

Question

Question:

Wiring [432000] - is the brown wire running lights and the red wire stop and turn? Thanks

asked by: Terry

0

Expert Reply:

You are correct. The wires on the Peterson Round Trailer Tail Light with License Plate Light, part # 432000, are as follows. The brown wire is the running light circuit and the red wire is the stop and turn signal circuit. The light gets grounded through the mounting bolts to the trailer frame so it will need to be mounted to a metal surface connected to the trailer frame.

expert reply by: Amanda

0

Answer 1

Dico was bought out by Titan who now offers 5-on 4-1/2 idler hub #DX22XR. This hub is rated for 2500-lb axles and includes bearings, races, grease seal, grease cap, and lug nuts. You can be assured it will fit the trailer spindle as long as the…

view full answer...

Answer 2

Unfortunately, I wasn't able to find any reference online for a Dico 16859 hub, but I can likely help find replacements for you. To properly cross reference your existing hubs to those we offer, I'll need you to identify the wheel bearings…

view full answer...

Answer 3

Trailer hitch wear and tear is a normal thing and comes from salt that is used on the road or from different objects flying up under your car and hitting the trailer hitch. Although keeping a used trailer hitch in mint condition is impossible, there…

view full answer...

Answer 4

The Curt Trailer Hitch Receiver- Class III #C13206 doesn't require stabilization strap #18050 any longer. Curt used to require it and has recently soften their wording to simply recommend because many customers were not happy with it. We are…

view full answer...

Answer 5

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 6

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 9

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 10

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 11

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 12

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Peterson Round Trailer Tail Light Wire Connections

Product Page this Question was Asked From

Continue Researching