Replacement EZ-Lube Grease Cap for Kodiak KH84545S

Question

Question:

i need the part number for the grease cap with the removable rubber to fit these hubs

asked by: Thomas F

1

Helpful Expert Reply:

The correct EZ-Lube grease cap for the Kodiak # KH84545S would be the TruRyde 2 inch # DC200L-DCRP. This is made of 22 gauge, zinc coated steel giving it good corrosion resistance.

expert reply by: Lazer S

1

Answer 1

The 3.5K Kodiak Disc Brakes - 10" Hub/Rotor #KOD99FR come with oil but if you need to replace it or add more in the future then you need the following: - Kodiak Synthetic Bearing Oil for Oil Bath Hubs #XLPROLUBE I've attached a video…

view full answer...

Answer 2

The races of the part #KH84545S are installed but the bearings and seal are sold separately. It calls for a #L68149 and #L44649 and then for a seal part #RG06-050 which all match what you say you need.

view full answer...

Answer 3

For a completely stainless steel version of the Kodiak Disc Brake Kit part #K2HR35D you will want to use the Kodiak Disc Brake Kit part #K2R35S. You will also need an idler hub like the Kodiak Trailer Hub part #KH84545S as the stainless steel…

view full answer...

Answer 4

Yes, you should have no problems using an Oil Bath System, like part #XLPROLUBE1980KIT, with a number 84 EZ Lube Spindle, like part #TRU74FR. A few things to keep in mind when installing an oil bath system. You will want to make sure that everything…

view full answer...

Answer 5

The choice of oil bath or regular hubs is up to the manufacturer. They are usually found on higher capacity axles, though as you know there are some on lower capacity axles. You can convert some hubs from grease to oil bath using a kit such as…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 8

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 9

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 10

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 11

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 12

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Replacement EZ-Lube Grease Cap for Kodiak KH84545S

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching