What is the Measurement from the Pin Hole to the Hitch Mounting Point of a Curt Hitch Receiver?

Question

Question:

The Thule EasyFold XT bike rack calls for the pin hole to be 1 1/2inch back from opening to accommodate the built-in pin. Looking closely at a C13416 video it appears to be. Ill find out when I open my just received C13416. This measurement might be helpful to others.

asked by: Richard D

0

Expert Reply:

I confirmed with Curt that the measurement from the pin-hole opening to the front of the hitch mounting point on the Curt Hitch Receiver # C13416 is 2-1/2 inches. With this measurement, the Thule EasyFold XT # TH903202 is compatible.

expert reply by: Bob C

0

Curt Receiver Dimensions
(click to enlarge)

Answer 1

Between the Curt Class III Trailer Hitch #C13416 and the EcoHitch #306-X7396 for your 2019 Toyota RAV4 the EcoHitch will provide slightly better ground clearance but it is going to require some trimming on the rear fascia to allow room for the…

view full answer...

Answer 2

In regards to the Curt Trailer Hitch Receiver part #C13416 which is a fit for a 2021 Toyota RAV4, the hitch pin hole is about 5" behind the rear bumper. The distance to the hitch ball would be dependent on the length of the ball mount. I am…

view full answer...

Answer 3

Still the same for the 2021 as it is still part of the same 5th generation of this model RAV4. The same the Draw-Tite Trailer Hitch, #DT82QR and Curt Trailer Hitch Receiver, #C13416 are being used without any redesign. The Draw-Tite Trailer Hitch…

view full answer...

Answer 4

With the Curt Trailer Hitch Receiver #C13416 installed on your 2019 Toyota RAV4 Hybrid Limited you should be able to activate the hands free liftgate function by kicking to either side of the receiver. I am attaching a photo that shows some locations…

view full answer...

Answer 5

If you check out the install picture I attached for the Curt hitch part #C13416 you can see that it hangs at the same height as the exhaust pipes and only sticks out a little bit past them so you'd have the same ground clearance you have now. Or…

view full answer...

Answer 6

After you install the Curt hitch part #C13416 on your 2019 Toyota RAV4 you'll have right at 10-1/2 inches of ground clearance measured from the bottom of the hitch to the ground. I attached an install video for this for you to check out as well.

view full answer...

Answer 7

The Curt Class III trailer hitch part #C13416 that you referenced does fit your 2021 Toyota RAV4 and comes with everything needed to install. You'd only need basic hand tools. I attached an install video for this for you to check out as well.

view full answer...

Answer 8

You actually won't need to trim any rear fascia when installing any of our trailer hitches on your 2020 Toyota RAV4. Out of our selection I recommend going with the Class III Curt Trailer Hitch #C13416 because it has a 2" receiver (so it is…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 11

To add a hitch to your 2024 Toyota RAV4, I recommend the etrailer item #e23ZR. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a 4,000 lbs towing capacity, and a 600…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

What is the Measurement from the Pin Hole to the Hitch Mounting Point of a Curt Hitch Receiver?

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching