Replacement Ball Platform for Anderson Rapid Hitch Ball Mount

Question

Question:

I have the Andersen Rapid hitch for a 2 1/2” receiver and need replace this part. Will this work with mine? This adjustable portion has a seized pin so I can not replace the ball assemble.

asked by: Stuart

0

Expert Reply:

Yes, the Replacement Ball Housing for Rapid Hitch part # AM3423 works with all of the Anderson Rapid Hitch Ball Mounts.

expert reply by: Conner L

0

Answer 1

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The…

view full answer...

Answer 2

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 3

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 4

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 6

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 7

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 8

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 9

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 10

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 11

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 12

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Replacement Ball Platform for Anderson Rapid Hitch Ball Mount

Product Page this Question was Asked From

Continue Researching