Extra Mounting Plates For Erickson Removable Motorcycle Wheel Chock EM07506

Question

Question:

Can I order extra anchor plates? I would like the versatility to move the chock to different locations in my trailer.

asked by: Roy O

0

Expert Reply:

Yes, you can order extra mounting plates for the Erickson Removable Motorcycle Wheel Chock # EM07506. Replacement Mounting Plates # EM56ZV is the part number you are looking for; this kit comes with 4. This allows you to move the chock to different locations in your trailer just as you were wanting to do.

expert reply by: Andrew N

0

Answer 1

The mounting points for the Tow-Rax Low-Profile Floor Track #TWSP72TA are spaced every 12" with the 6' track having 7 mounting holes. The hole opening will accept a 1/4" countersunk screw and I recommend using a stainless…

view full answer...

Answer 2

The mounting holes on the Tow-Rax Low-Profile Floor Track for Tie-Down Anchors part #TWSP72TA are 1/4" diameter.

view full answer...

Answer 3

I did some research and found that the Erickson O-Track Cargo Control System like part #EM59133 is very similar to the L-Track systems you referenced. The Erickson O-Track is 18 inches long and includes 2 Spring-loaded O-ring clips and mounting…

view full answer...

Answer 4

The MaxxTow wheel chock #MT70075 is discontinued. An easier solution is the Erickson #EM07506 Removable Motorcycle Wheel Chock which can take wheels up to 6" wide and can be easily removed when not needed.

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

I checked with Erickson and their Removable Motorcycle Wheel Chock item #EM07506 does not have a weight rating. It is made of steel and works with bikes that have up to 6" tires. So long as your Honda and Kawasaki do not have wider tires…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Hi Bruce, To lift your trailer we'll first need to check of the suspension and see if you have torsion axles or a leaf spring suspension. If you have torsion axles then I'll need to see the axle tag in order to determine what you have so I…

view full answer...

Answer 10

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 11

The Rhino-Rack Heavy-Duty Roof Rack Roof Rack have specific C-channels that are designed to fit specific Rhino-Rack Heavy-Duty accessories, like the Rhino-Rack Hi-Lift Jack and Shovel-Holder Brackets #RRRCB-RSHB-RJHB as an example. That's the…

view full answer...

Answer 12

According to Rhino Rack, if you were to go with the shorter bars, you'll only have 1-1/4 inch of leeway on each side which isn't enough in their opinion. I'd recommend going with the 71 inch bars so you'll be certain of a good fit. As…

view full answer...

Extra Mounting Plates For Erickson Removable Motorcycle Wheel Chock EM07506

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching