Which B&W Turnoverball Gooseneck Hitch Fits a 2008 Chevy Silverado 2500 HD Short Bed

Question

Question:

I am looking to purchase the BandW gooseneck hitch for my 2008 chevy 2500 hd 6-1/2 ft bed. Is the BWGNRK1067 the correct item for my truck ? Thanks

asked by: Adolph

1

Helpful Expert Reply:

Yes. The B&W Turnoverball Underbed Gooseneck Trailer Hitch w/ Custom Installation Kit - 30,000 lbs # BWGNRK1067 is a confirmed fit on your 2008 Chevy 2500 HD with a 6-1/2 Foot Bed.

expert reply by: Erik B

1

Answer 1

The mounting hardware by itself is not available for the B&W Turnoverball Underbed Gooseneck Trailer Hitch #BWGNRK1067 for your 2007 Chevy Silverado 2500, but you can get the installation kit. This comes with all of the hardware, as well as the…

view full answer...

Answer 2

The B&W Turnoverball Underbed Gooseneck Trailer Hitch, part #BWGNRK1067 includes the installation kit for the trailer hitch and does include a bracket to re-install the factory braking system as mentioned at the 3 minute 18 second mark on the…

view full answer...

Answer 3

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 7

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 8

There is a difference between a 7-way round and and 7-way rv blade connector. If you take a look at the accompanying photo, which is from our linked article on trailer wiring you can see that the connector on the left has blade-style pins while the…

view full answer...

Answer 9

The recommended minimum clearance between gooseneck trailer overhang and truck bed rails is 4-6 inches. I'd recommend 6 inches but a lot of people get by with just 4. Ideally you have at least 6 inches of clearance and the trailer is sitting…

view full answer...

Answer 10

Yes, anytime you use a hitch extender or reducer like #HR26 you will lose about 1/3 of your hitches overall capacity. However, since you'll be towing a trailer that weighs between 4,500 to 5,000 lbs, the Brophy Hitch Reducer #HR26 will still work…

view full answer...

Answer 11

I went out into our warehouse and measured both the Curt Hitches you referenced #C15312 and #C15313. THe #C15312 measures 2-3/4 inches from the mounting flange down to the hitch opening and the #C15313 measures 5-5/8 inches.

view full answer...

Answer 12

It sounds like you have a 7-way blade connector on your boat trailer as that is a very common connector on boat styles. This connector has 6 pins around the outside of the connector and a center pin for a total of 7. Part #A7WCB would be what a 7-way…

view full answer...

Which B&W Turnoverball Gooseneck Hitch Fits a 2008 Chevy Silverado 2500 HD Short Bed

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching