Correct Curt Front Mount Trailer Hitch for a 2004 Ford F-350

Question

Question:

I have a 2004 F350 super duty will the hitch# C31014 fit this truck. I saw the video of it being put on a f250.

asked by: Eric E

0

Expert Reply:

I do have an option for you but the only Curt Front Mount Trailer Hitch Receiver option for a 2004 Ford F-350 is part # 31114.

expert reply by: Conner L

0

Answer 1

There are virtually no structural differences between the Curt Front Mount Trailer Hitch Receiver part #31114 and the Draw-Tite Front Mount Trailer Hitch Receiver part #65022 for your 2000 Ford F-250. They both install in the exact same location…

view full answer...

Answer 2

This is correct. If you have the Blocker Beam on your 2006 Ford F-350 you will need to use the Draw Tite hitch #65022 or if not you'd need the #31114. The blocker beam is a small sub-bumper behind air dam.

view full answer...

Answer 3

What you are referring to is the lower front crossmember, and if your 2007 Ford F-350 Super Duty does have that crossmember you can definitely install the Curt Front Mount Trailer Hitch Receiver #31114. You will simply remove it (starting at about…

view full answer...

Answer 4

The difference between the Curt Hitch #C31014 and Curt Hitch #31114 is that the #C31014 is designed for vehicles with blocker beams and the #31114 is designed for vehicles without the blocker beam. You will want to look under the front end of your…

view full answer...

Answer 5

If you do not have the blocker bar or sub-bumper behind the air dam, the Draw-Tite #65022 would a good choice for your 2000 F250. According to the installation instructions, the tow hooks are temporarily removed but are re-installed later in the…

view full answer...

Answer 6

The instructions for both of the front-mounted hitches that are a fit for your 2003 Ford Excursion, the Draw-Tite #65022 and Curt #31114 reference the blocker beam, saying you'll need to remove and then reinstall it when putting on either hitch.…

view full answer...

Answer 7

The front mount trailer hitch I recommend for your 2005 Ford F-350 is the Curt Front Mount Trailer Hitch Receiver part #31114 because it is made in the USA and currently our most cost effective option for a front mount hitch. I called Curt and they…

view full answer...

Answer 8

The Curt Front Mount Trailer Hitch Receiver part #31114 which is a fit for a 2007 Ford F-250 Super Duty installs behind the bumper beam to the end of the frame on both the driver and passenger side. I have attached a photo below which shows this.…

view full answer...

Answer 9

The primary difference between the Draw-Tite #65022 and the Curt #31114 is that they're manufactured by two different companies. The hitches are nearly identical in appearance, have the same weight ratings and would install in the same manner.…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Correct Curt Front Mount Trailer Hitch for a 2004 Ford F-350

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching