Parts Needed to Add 7-Way to 2018 Jeep JL Wrangler

Question

Question:

What is the easiest way to add a seven pin to the Curt C56407 on a 2018 Jeep jl sport.

asked by: Mario B

0

Expert Reply:

We can get your 2018 Jeep JL Wrangler set up with a 7-way, and there are a couple of parts needed, as the only way to add the 7-way is by hardwiring one in. You do have the first part that is required, which is the 4-way, the Curt T-Connector Vehicle Wiring Harness # C56407.

Then, in order to add the 7-way connector, circuit breakers and rest of the hardware needed for installation you will need the following part:

- Universal Installation Kit for Trailer Brake Controller # ETBC7

This will allow you to wire the 7-way in your Jeep so you can add a trailer brake controller. I have added a link below to a video review as well as a help article on installation for you to check out if you'd like to take a look.

If you also need a brake controller for your Jeep, my favorite option is from Draw-Tite due to the value it gives you with its unique combination of quality and cost-effectiveness. The wiring harness and controller are the Tekonsha Custom Wiring Adapter # 3073-P and Brake EVN # TK63VR.

expert reply by: Kyle S

0

Answer 1

Yes, there is! To install the Redarc Tow-Pro Elite Brake Controller item #RED63RR in your 2023 Subaru Ascent you will need the Plug-In Wiring Adapter for Electric Brake Controllers item #3062-P. The brake controller port will be underneath the dash…

view full answer...

Answer 2

Increasing the tire and wheel size can increase the height of the trailer but it's usually quite minimal. Before you do anything else you should see if the pin box can be adjusted. Although you have to be careful here since This will lower the…

view full answer...

Answer 3

That is correct. If your 2021 Wrangler Unlimited has the connector located under the dash to the left of the steering column near the top of the e-brake pedal as shown in the provided photo, you'd use the #3073-P harness to connect the #90195…

view full answer...

Answer 4

The brake controller that I recommend for your 2022 Jeep Gladiator with tow package is the Tekonsha Prodigy P3 Trailer Brake Controller #90195 which will use the Tekonsha Custom Wiring Adapter for Trailer Brake Controllers #3073-P to plug into your…

view full answer...

Answer 5

The SumoSprings Solo Custom Helper Springs item #SSR-405-47 that fit a 2012 - 2023 Jeep Wrangler should have a 1/2" to an 1" of space between them and your axle.

view full answer...

Answer 6

What you describe is called 'cupping', where the tire looks like something's been taking bites out of it. Usually cupping on a tire is caused by the tire bouncing on the road, which can have many causes. Check the air pressure in your…

view full answer...

Answer 7

We have direct replacements for the two brake assembly part numbers you listed. You would want part #AKEBRK-35R and #AKEBRK-35L. Or, for never adjust assemblies the part #AKEBRK-35L-SA and #AKEBRK-35R-SA would work as well. Most likely you have a…

view full answer...

Answer 8

I recommend using the Redarc Tow-Pro Elite Brake Controller #RED63RR with your 2022 Jeep Gladiator. You will use the Plug and Play Harness #3073-P to connect to the tow package factory wiring on your Jeep. I prefer the Redarc as it hides the main…

view full answer...

Answer 9

You will need several items to add electric brakes to your Carry-On Utility trailer. Starting with the trailer you will need a hub and drum that matches the bearings and seal on your trailer spindle and your wheel bolt pattern. The only way to be…

view full answer...

Answer 10

The wiring harness included with the #TL16RK LED Trailer Lamp/wiring kit would work perfectly fine zip tied to the trailer frame (or you could use the clips included with the kit). I'd recommend running the wires on the inboard side of the frame…

view full answer...