What Replacement Parts Are Available for an etrailer MJ-1200B or Fulton Swivel Marine Jack

Question

Question:

Id like to purchase parts to a trailer jack, etrailer or fulton, either one will work. Im looking for the main tube, swivel, and mounting bracket for MJ-1200B or FXP10W0301. I need 2. Im not repairing an existing stand. Will purchase used or slightly damaged. Thanks.

asked by: Larry J

0

Expert Reply:

You can replace the mounting bracket and hardware on an # FXP10W0301 or # MJ-1200B, but the tube and swivel bracket are not available as replacement parts for these jacks. You can use the Replacement Mounting Kit for etrailer and Ram Swivel Marine Jacks - 1,200 lbs and 1,500 lbs # MJ-1000B-MK for the mounting bracket and Replacement Mounting Hardware for etrailer and Ram Swivel Marine Jacks - 1,200 lbs and 1,500 lbs # MJ-1000B-MBB for the hardware. You can also replace the inner bearing with the # MJ-1000B-BR.

Unfortunately as I mentioned, the main tube is not available as a replacement part so if that is damaged you would need to replace the entire jack. You can use the # FXP10W0301 or # MJ-1200B as the replacements.

expert reply by: Erik B

0

Answer 1

The Replacement Bearing for etrailer and Ram Round, Topwind Jacks #TJA-2000-BR has an inner diameter of 0.5", an outer diameter of 1.025", and a thickness of .477". When you go to install this bearing, you'll want to put the thrust…

view full answer...

Answer 2

Boat jacks, including the Fulton jack you have, are typically constructed so that the inner tube of the jack and the yoke and caster are all one piece. Because of the way its constructed, the caster won't easily turn until the boat is rolling.…

view full answer...

Answer 3

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 4

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 5

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 6

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 7

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 8

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 9

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 10

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 11

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 12

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...