Fit of Phoenix USA PXQ2020XL Center Cap on 1999 Newmar Dutch Star Spartan Motorhome

Question

Question:

Will the 8 1/4 inch rear center cap fit on a1999 newmar durch star spartan. Thank you

asked by: Rick W

1

Helpful Expert Reply:

The Phoenix USA # PXQ2020XL wheel center cap isn't vehicle specific. If the rear wheels on your 1999 Newmar Dutch Star Spartan motorhome has a 8-1/4 inch diameter hub and a 10 on 285mm wheel bolt pattern, then the center cap would be compatible. Unfortunately, I have no way of looking up the hub size and wheel bolt pattern of your motorhome.

expert reply by: Mike L

1

Answer 1

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 2

Even though most threads on bolts use right-handed bolts/nuts, some special scenarios warrant a left-handed thread. When wheel accessories like the Phoenix USA Rear Wheel Center Cap - 8-1/4" Hub Diameter - Center Hole Mount - Left Thread…

view full answer...

Answer 3

I spoke to my contact at Phoenix USA and he told me the correct part for your 2007 Winnebago Tour 40TD Motorhome is the Replacement Right Thread Mounting Bracket for Phoenix USA Wheel Center Caps for 8-1/4" Axles #PHX67FR.

view full answer...

Answer 4

The Phoenix USA Rear Wheel Center Cap - 8-1/4" Hub Diameter - Center Hole Mount - Right Thread #PXQ2020XL fits the rear motorhome wheels that has a hub diameter of 8-1/4 inches and a bolt pattern of 10 on 285 millimeters. When it comes to the…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 7

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

The torque for the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles - 12" - 5 Spoke Utility #8-174-5UC3 is not specified by the manufacturer. For 9/16 inch studs, the typical lug nut torque will be 120-140 ft lbs based on most…

view full answer...

Answer 10

I'd be happy to help you out, John! To replace the brakes on your 5th wheel trailer you need the etrailer Electric Trailer Brakes #AKEBRK-7-SA which come with a self-adjusting feature so once you initially set them up you won't have to adjust…

view full answer...

Answer 11

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 12

The "KTC 7600" stamped on the brake pad doesn't look to be a part number, so I can't cross reference it, but we do know you have Kodiak ceramic brake pads. So to determine the correct brake pads, all you need to do is match up…

view full answer...