Could CE Smith Bunk Bracket be Adapted to Fit Smaller Bracket

Question

Question:

Hi - are there brackets for 2.5’ or 2’ square tube?

asked by: Richard F

0

Expert Reply:

Since there isn't a smaller bracket setup for the CE Smith Heavy Duty, Vertical Bunk Brackets # CE10160GA-2 best option might be to use spacers to take up the extra space and provide the tighter fit.

expert reply by: Jameson C

0

Answer 1

The correct torque spec for trailer suspension u-bolts will depend on the the diameter of the bolt. You will want to use the following depending on bolt size: 1/2" bolts: 45 ft/lbs - 70 ft/lbs 9/16" bolts: 65 ft/lbs - 95 ft/lbs 5/8"…

view full answer...

Answer 2

It is recommended to cover all of the exposed wood. When the wood is exposed there is a greater risk of rot and damage. The carpeting is made of breathable polyester which makes sure it can dry out so no mold will build up and damage the wood or…

view full answer...

Answer 3

If you are wanting to use vertical bunk brackets like the CE Smith Heavy Duty, Vertical Bunk Brackets - 90 Degree - Galvanized Steel - 6" Tall - Qty 2 #CE10160GA-2, I recommend using them on the front and rear of the trailer. You will also need…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 6

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 7

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 8

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 9

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 10

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 11

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 12

The torque for the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles - 12" - 5 Spoke Utility #8-174-5UC3 is not specified by the manufacturer. For 9/16 inch studs, the typical lug nut torque will be 120-140 ft lbs based on most…

view full answer...

Could CE Smith Bunk Bracket be Adapted to Fit Smaller Bracket

Product Page this Question was Asked From

Continue Researching