Does Stealth Hitch SH23VR Fit 2015 BMW X1

Question

Question:

Hello, Im looking for hit equipment and found here this one Stealth brand for my BMW X1. I want to double confirm that is fit on my car SH23VR

asked by: Dongjun K

0

Expert Reply:

The Stealth Hitch part # SH23VR is a confirmed fit for your 2015 BMW X1.

expert reply by: Jameson C

0

Answer 1

You can select your new hubs by matching up your axle weight rating, wheel bolt pattern and the bearings used in your current hubs. Based on my research your hubs are 10 x 2-1/4-inches, are from a 3500-lb axle and have the 5-on-4-1/2 bolt pattern.…

view full answer...

Answer 2

From what I have found, the replacement for the AL-KO 7230 hub and drum assembly is the Trailer Hub and Drum Assembly - 3,500-lb Axles - 10" Diameter - 5 on 4-1/2 - Pre-Greased #AKHD-545-35-K. For brakes, I recommend the Electric Trailer…

view full answer...

Answer 3

The Trailer Hub and Drum Assembly part #AKHD-545-35-K is the correct replacement for an AL-KO 7230. In regards to the braking assemblies, I suggest getting a new pair, the Electric Trailer Brake Kit part #AKEBRK-35-SA. This option will save you…

view full answer...

Answer 4

We aren't manufacturers of those parts, and we don't have the testing ability in house, so I reached out to a couple of our manufacturers to see what information they could provide to try and help. I reached out to my contact at Curt…

view full answer...

Answer 5

On seat cover #AA3142B the back side has a non-skid type of material that will grip the seat portion and the seat back to help prevent it from coming out of position. It is still possible, if conditions are right, for it to come out of position. I…

view full answer...

Answer 6

The Third Brake Light Camera part #3460002 that you referenced is not available without a switch, this comes with a gasket which provides the seal but also silicone sealant/butyl tape is recommended, the factory screws of your truck are long enough…

view full answer...

Answer 7

Dexter did acquire AL-KO axles and the Dexter Trailer Hub and Drum Assembly for 3,500-lb Axles - 10" Diameter - 5 on 4-1/2 #84546UC3 is the full assembly replacement. If you just wan to replace the bearings and seal then you will want #L44649,…

view full answer...

Answer 8

For your AL-KO 7230, the replacement wheel stud you most likely need is the 1/2" Diameter x 2" Long - Qty 1 #7-122. This is the replacement for the Dexter Hub that replaced the AL-KO hub when Dexter bought them out. This should work well on…

view full answer...

Answer 9

If you already have brake drums you will not have to replace them unless they are damaged or became overheated and have discoloration on the inside armature surface where the magnet rides, grooves in the armature surface, or severe wear where the…

view full answer...

Answer 10

If the surface on the inside of the drum where the shoe pads make contact isn't smooth then a brake shop may be able to turn the drums. If that surface or the surface where the magnet makes contact (called the armature surface) is discolored then…

view full answer...

Answer 11

After you've packed the bearings and assembled everything, carefully slide the hub assembly onto the spindle and install the outer bearing. Install the spindle and tang washer and run the spindle nut down finger tight, then rotate the hub back…

view full answer...

Answer 12

In order to find out which hub and drum assembly fits your 3,500 lb axle on your Cargo Craft trailer you will need to know which bearings are on your axle. If you have a serial number on the axle you can probably get this information from the…

view full answer...

Does Stealth Hitch SH23VR Fit 2015 BMW X1

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching