Recommended Solution for Dragging Hitch Receiver on 2002 Ford Van

Question

Question:

i bought a Curt Trailer Hitch Receiver - Custom Fit - Class IV - 2 Item # 14055 from you and I am looking for a a skid wheel to fit the hitch. What would you recommend

asked by: Steven D

1

Helpful Expert Reply:

The best solution for this is going to be the Roadmaster Rollaway Trailer Hitch Protector # RM-050, which will work when you're towing as long as whatever is in the receiver doesn't hang below the Rollaway. This is ideal because it doesn't require any welding on, so it's ready to be installed right out of the box and will keep your hitch from getting dinged up when ground clearance isn't the best.

I've linked our review video of this part for you to check out.

expert reply by: Erik B

1

Answer 1

Thanks for the pictures! The Ultra-Fab Hitch Mounted Steel Rollers for RVs w/ 2-1/2" Hitch Tubing #UF48-979017 would work great for your 2022 Jayco Pinnacle 38FLGS, and would eliminate the dragging you're experiencing. Adding the Roadmaster…

view full answer...

Answer 2

The Roadmaster Rollaway Trailer Hitch Protector #RM-050 will likely work with your trailer hitch that has the tabs on the bottom of the receiver as there does not look like there is going to be any interference. So long as the tabs are completely on…

view full answer...

Answer 3

I do have an option for you but the Curt Trailer Hitch Receiver part #13390 on your 2015 Subaru Legacy already has the highest ground clearance (10-1/4") of any other trailer hitch receiver we have confirmed to fit your vehicle. This measurement…

view full answer...

Answer 4

Hey Philip so while we don't carry the exact spring you are looking for it does match the specs of the #e59SR so this would be a great solution. It's correct length at 23-1/8 inches and is for a 3,500 lb trailer axle like you have as well.

view full answer...

Answer 5

Thank you again for ordering with etrailer.com, we appreciate your business. I have attached a scan of the installation instructions for the Dexter Trailer Springs Over-Under Conversion Kit, #K71-384-00.

view full answer...

Answer 6

It sounds like you are needing to install a 7-Way connector at the rear of your 2005 Ford E-150. If your Ford Van did not come with the factory tow package (with a 7-way connector), then there will not be a built in socket or harness under the…

view full answer...

Answer 7

For your RV built on the 2003 Ford E-450 chassis, I recommend looking at the Curt Adjustable Width Trailer Hitch Receiver #C13702. This is a universal, adjustable trailer hitch designed specifically for use on RVs. It can be bolted to the vehicle…

view full answer...

Answer 8

The best place to start for tow bar lighting for your 2023 Jeep Wrangler will be the Roadmaster kit part #RM-15267 which once installed puts a 6-way on the front of the Jeep and then to complete the charge circuit all you would need is the part…

view full answer...

Answer 9

To replace the factory hitch on your 2002 Ford E-350 Super Duty Van you can use the Draw-Tite Ultra Frame #41945 which has the bolt holes 38-5/8" apart (center on center). This hitch will be the perfect replacement for your factory hitch.…

view full answer...

Answer 10

If you have a vehicle specific wiring harness for a brake controller then that would indicate that you have a factory tow package and subsequently would already have a 7-way at the back of your vehicle. The universal 7-way connector #ETBC7 is meant…

view full answer...

Recommended Solution for Dragging Hitch Receiver on 2002 Ford Van

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching