Locking Pins for Mount of B&W Tow & Stow 2-Ball Mount

Question

Question:

Hi, I am looking at the BW Tow and Stow hitch. Was wondering if a locking pin is available for the adjustable pins instead of the carter key pins that hold them secure? Thanks!

asked by: Chris D

0

Expert Reply:

Yes, there are locking pins available for the ball mount portion of the B&W Tow & Stow ball mounts, and they will fit the 10,000 lb capacity and 14,500 lb capacity Tow & Stow ball mounts.

The correct part is the InfiniteRule Locking Pins for B & W Tow and Stow 10K and 14.5K Ball Mounts # 34061775-D.

This actually comes with four locks, one to secure the entire ball mount to your hitch receiver, two to secure the ball platform to the ball mount, and one to secure the balls to the ball mount platform. The locking pins will fit each of the 10k Tow & Stows such as the B&W Tow & Stow 2-Ball Mount - 2" Hitch - 3" Drop, 3-1/2" Rise # BWTS10033B, as well as the 18k options such as the B&W Tow & Stow 2-Ball Mount - 2-1/2" Hitch - 7-1/2" Drop/Rise # BWTS20040B.

The 10k ball mounts are only a fit for 2 inch hitches while the 14.5 k mounts only fit 2-1/2 inch hitches. I have added a link below to our entire selection of both 10k and 14.5k for you as well.

expert reply by: Kyle S

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 3

Hey Tim, thanks for the picture of your current brake assemblies. While what you have doesn't look exactly like a free-backing setup you definitely can replace what you have with them. For that I would go with the etrailer part #AKFBBRK-35 which…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Hi Larry, So we have a couple bumpers that may work, though each is 96 inches long. They can be cut to length though, and the difference is their width, as one is 3" wide and the other 4" wide to fit different size bumpers: - Pre-Drilled…

view full answer...

Answer 7

Based on the information you provided either the Titan Hydraulic Brake Kit - Free Backing - 10" - Left and Right Hand Assemblies - 3,750 lbs #T4071600-500 or #T4423500-400 will fit your drums. The only difference between these two brakes is the…

view full answer...

Answer 8

I checked with Erickson and their Removable Motorcycle Wheel Chock item #EM07506 does not have a weight rating. It is made of steel and works with bikes that have up to 6" tires. So long as your Honda and Kawasaki do not have wider tires this…

view full answer...

Answer 9

The Firestone Heavy Duty Air Compressor item #F9499 can be mounted in any position or orientation. Firestone recommends it be installed on the frame rail of your 2016 Toyota Tundra. There is no specific spot the compressor is supposed to be…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

Hey Dustin, thanks for reaching out! I will recommend SumoSprings over Timbrens all day everyday because they are much more forgiving when the vehicle is unloaded. We've actually joked around here about how the Timbren kits will either give you…

view full answer...

Answer 12

Normally trailer coupler height is around 17 inches, from the ground to the bottom of the coupler, and most hitch manufacturers design their hitches to work with a ball mount that will end up very close to this measurement. I am including a link to…

view full answer...