Hub/Drum for Trailer that Has a 5 on 4-3/4 inch Bolt Pattern

Question

Question:

Hello, Do yall have any electric kits with a 5 on 4 3/4 bolt pattern? Thank you,

asked by: Shawn B

0

Expert Reply:

Yes we have hub drums like the part # AKHD-5475-35-EZ-K that has a 5 on 4-3/4 inch bolt pattern like you want and is for 3,500 lb axles.

expert reply by: Jameson C

0

Answer 1

If your trailer has 7 wires running all the way back to the brakes, then yes, you can tap into the existing wiring. Each of your new brakes will have two wires for the brake magnet. One wire is for 12 volt power to the brake magnets and the other…

view full answer...

Answer 2

Based on the brake mounting flange dimensions you have you can easily install brake assemblies like the #AKEBRK-35-SA which will bolt right up. The trick though is going to be picking out the correct hub/drums for your spindles so that we can then…

view full answer...

Answer 3

There are a number of reasons why the brakes on your trailer may not be working. Lets start with the easiest things to check. First, check the vehicle and trailer connectors for corrosion. This can cause a short inside the connector and the brake…

view full answer...

Answer 4

Trailer brakes do not lock up when they are disconnected from the tow vehicle. They basically are free rolling until a brake controller puts amperage on their circuit which applies the braking mechanisms. Wheel chocks like what you mentioned are…

view full answer...

Answer 5

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 6

Hey Jeremy, Typically with boat trailers the manufacturer will install hydraulic surge brakes because you don't have to worry about the water damaging wires like you would with electric brakes. That being said, if you use a heat shrink butt…

view full answer...

Answer 7

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 10

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

I currently have three diffrent self-adjusting assemblies for your boat trailer with 10" x 2-1/4" electric drum brakes which are attached for you below. eTrailer Electric Trailer Brake Kit part #AKEBRK-35-SA (3,500 Axles) Dexter…

view full answer...

Hub/Drum for Trailer that Has a 5 on 4-3/4 inch Bolt Pattern

Product Page this Question was Asked From

Continue Researching