Rubber Piece to Prevent Safety Chains From Falling Off

Question

Question:

Do you carry the rubber piece that goes on safety chain hooks that keep them from falling off?

asked by: Jim D

0

Expert Reply:

It sounds like you're needing some safety chain keepers. We offer those as part # CE16691A.

expert reply by: Mike L

0

Answer 1

First thing you will need to do is determine how much rise/drop you would need from a ball mount to tow your trailer level. For that you will want to check out the help article that I attached that details how to do this. Once you figure out what you…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 7

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 8

Normally trailer coupler height is around 17 inches, from the ground to the bottom of the coupler, and most hitch manufacturers design their hitches to work with a ball mount that will end up very close to this measurement. I am including a link to…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

Hey Antoine, so the two kits you mentioned are actually really similar and honestly I would go with the part #ETBC7 if I were you. The #ETBC7L is basically the same thing minus a couple wires and breakers so you may as well get the kit that has…

view full answer...

Answer 11

There is a way for you to not only lock the B&W Tow & Stow 3-Ball Mount - Compatible with GM MultiPro Tailgate - 2.5" Hitch - 148K #BWTS20067BMP to your 2-1/2 inch trailer hitch, but also the ball platform to the mount, and the hitch…

view full answer...

Answer 12

Hi Robert, The Curt Pintle Hook #C45908 would require that your EZ Loader boat trailer has a lunette ring for the coupler. From what I can see the 26-30ET should have a surge brake coupler that would couple to a standard ball mount. You'll need…

view full answer...

Rubber Piece to Prevent Safety Chains From Falling Off

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching