Does Buyers Products Hitch 3371809060A Fit 2002 Ford F-250

Question

Question:

Will this item# 3371809060A fit the ford 2002 F250 Super Duty or do you have another Back plate with receiver that will? It comes up in the search, but claims F350 and up.

asked by: Roger O

1

Helpful Expert Reply:

If your 2002 Ford F-250 is a cab and chassis model the Buyers Products hitch plate part # 3371809060A will fit.

The cab and chassis model trucks are sold without a bed and have a frame width 34 inches.

expert reply by: Jameson C

1

Answer 1

Yes, you can remove your weld-on coupler and install a new bolt-on coupler that fits a 2 inch ball. There is just a few things you need to do to before and when installing. You need to know what channel size and the weight capacity you will need for…

view full answer...

Answer 2

The Buyers Products Flatbed/Flatbed Dump Hitch Plate Bumper with 2" Receiver #3371809055 is designed or flatbeds and flatbed dump trucks. While it is ready to mount on Ford trucks, there is some drilling required for GM trucks. This hitch is a…

view full answer...

Answer 3

Yes the Hydrastar Disc Brake Kit for 7k axles part #HSE7K-T1SO fits Dexter and LCI/Lippert 7k axles as they use the same spindle dimensions and brake mounting flange dimensions.

view full answer...

Answer 4

To convert your Dexter 7k torsion tandem axle trailer to disc and electric over hydraulic we actually have a kit that comes with everything. All you'd need is HydraStar Disc Brake Kit w/ Actuator for Tandem Axle Trailers #HSE7K-T1. This comes…

view full answer...

Answer 5

You are correct, the Hopkins LED Breakaway Switch, #HM20059, does have 3 wires. The white wire is the ground wire and should be attached to the trailer frame. The blue wire on the switch will connect to the electric brake wire coming from the trailer…

view full answer...

Answer 6

I have attached the installation instructions for the Hopkins Engager Trailer BreakAway Kit, part #20099. This kit includes a charger and an LED tester and will work with single and tandem axle trailers. I have also attached a link to an installation…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 11

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 12

I definitely understand being a bit overwhelmed by the amount of options in front of you, however I can definitely help with differentiating the trailer hitches for your 2019 Subaru Outback Wagon along with explaining my personal recommendation,…

view full answer...

Does Buyers Products Hitch 3371809060A Fit 2002 Ford F-250

Product Page this Question was Asked From

Continue Researching