Tailgate Lift Assist for 2020 Nissan Frontier

Question

Question:

i like to know will the tail gate assist fit on a 2020 nissan frontier if so can you like if dose i like to order one for my truck. thank you.

asked by: David R

0

Expert Reply:

The part you asked about, the DeeZee Tailgate Assist Custom Tailgate-Lowering System # DZ43300 is a custom-fit item for specific trucks. Sadly, we don't have any custom-fit lift assists that match your vehicle.

We do have a "universal" fit lift assist, which is the Hopkins EasyLift Truck Bed Tailgate Lift Assist # 74211. However, this is not confirmed to fit on any Nissan trucks. I spoke with my contact at Hopkins and they could not confirm either if it was a fit. Some information I did get though was that the tailgate must be removable and be at least 62 inches in width and 19 inches tall.

I attached the video review of this product. You can see there that some drilling needs to be done on the tailgate and the truck tailgate post. Check your 2020 Nissan Frontier's tailgate and if it matches the requirements I mentioned, then you can give it a try!

expert reply by: Evangeline M

0

Answer 1

I called my contact at DeeZee about your 2014 Ram 1500. They told me they have never seen a truck that did not have the hole in the tailgate located near the pivot point on the driver's side. I recommend contacting the dealership to see if they…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 4

On GM vehicles of that vintage, the 12-V pin should be hot regardless of whether the ignition is on or not. If it isn't showing voltage even with the ignition on, you're almost certainly on the right track thinking it's a blown or…

view full answer...

Answer 5

The support capacity per etrailer Camper Jack #TJ01RT-HD that you referenced is 1,000 lbs. Since your trailer would weigh up to 5,000 lbs this would not be your best option as the jacks most likely would get exceeded. I'd go with scissor jacks on…

view full answer...

Answer 6

According to the owners manual for the 2011 GMC Sierra the brake controller fuse is in location 6 in the engine compartment fuse block. Consult your owners manual to confirm.

view full answer...

Answer 7

I have a solution for you, but a ladder rack may not be the answer. While we have the DeeZee Invis-A-Rack Folding Ladder Rack #DZ951601 for 6 foot beds or #DZ951551 for 5 foot beds, we do not have a tonneau cover that will work with this ladder rack.…

view full answer...

Answer 8

The manufacturer DeeZee does not list the Tailgate Assist Custom Tailgate-Lowering System part #DZ43102 as a fit for a 2013 Chevrolet Avalanche LTZ. However, we have had two separate reviews which I have attached for you that state the product will…

view full answer...

Answer 9

We do offer a tailgate assist for your 2001 Dodge Ram from Hopkins, part #74211. The Hopkins EasyLift is a torsion spring that helps control the descent of the tailgate when you're opening it but the spring action removes much of the weight of…

view full answer...

Answer 10

Thank you for your purchase of the Curt A16 5th Wheel Trailer Hitch #C16120 from etrailer, and the two bolts on the side of the head unit #C16520 should not be coming loose. According to Curt, you should make sure those two bolts are torqued to 175…

view full answer...

Tailgate Lift Assist for 2020 Nissan Frontier

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching