Recommended Grille Guard for 2020 Ford F-250 with Front Camera or Sensors

Question

Question:

Looking for a Bull Bar or a Grill Guard that will fit a 2020 Ford F-250 that will not interfere with the front cameras or sensors.

asked by: Peter D

0

Expert Reply:

The Westin Sportsman Grille Guard - 1 Piece - Black Powder Coated Steel # 40-3905 is my recommendation for your 2020 Ford F-250. The Parking Sensor Relocation Kit for Westin Sportsman Grille Guard # 40-0005S will also be needed.

There is not a grill guard or bull bar that doesn't require the relocation kit for the sensors.

expert reply by: Jason S

0

Answer 1

The Lippert Components Power Stabilizer Trailer Jack #LC298707 has a unique wiring connection. I've attached the diagrams for the switch so you can determine the correct connection. I'm assuming your black and white wires pictured are black…

view full answer...

Answer 2

I attached a picture that I got from Lippert that shows the wiring diagram for their stabilizer jacks like the part #LC298707.

view full answer...

Answer 3

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 4

Assuming your Sprinter has the factory tow package with the 7-way at the rear bumper, in addition to the #RED24FR Redarc Tow-Pro Liberty Brake Controller, you'll also need the #3063-P wiring harness and the #331-TPH-017. The connector to install…

view full answer...

Answer 5

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 6

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 7

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 8

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 11

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 12

What you need for your Isuzu NPR truck is a powered converter #C59236. It is compatible with incandescent and LED trailer lights. I have included a link to the installation instructions for you. This harness does require a direct connection to the…

view full answer...

Recommended Grille Guard for 2020 Ford F-250 with Front Camera or Sensors

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching