Installation of Lippert Stabilizer Trailer Jack # LC298707

Question

Question:

The motor has a red and black wire the Rv has a white and black What would be the correct way to wire Black to black red to white

asked by: Nelson G

0

Expert Reply:

The Lippert Components Power Stabilizer Trailer Jack # LC298707 has a unique wiring connection. I've attached the diagrams for the switch so you can determine the correct connection. I'm assuming your black and white wires pictured are black (hot) and white (ground) from your battery. The colors won't match, but the diagrams will help you connect the wires to the proper locations based on function.

expert reply by: Jason S

0

click to enlarge

Answer 1

I attached a picture that I got from Lippert that shows the wiring diagram for their stabilizer jacks like the part #LC298707.

view full answer...

Answer 2

You will want to use a minimum of 10 gauge wire like #10-1-1 from the battery to the motor on the Lippert High-Speed Power Stabilizer Jack #LC298707. I do not recommend running a front and rear stabilizer to the same power wire. Each wire uses a…

view full answer...

Answer 3

I attached a picture that shows the install instructions for the Lippert Components High-Speed Power Stabilizer Jack #LC298707 that you referenced and in it you'll notice a set distance isn't specified for where it has to install on the…

view full answer...

Answer 4

I definitely understand how safety chain capacities and determining exactly what chain rating you need for your trailer can be a bit confusing. To keep it as simple as possible, safety chain requirements state that the breaking strength of EACH…

view full answer...

Answer 5

The Camco RV Drain Trap part #CAM37262 is designed to screw onto the bottom of a sink and then ran outside the trailer with a drain hose similar to the Camco RV Drain Hose w/ Drain Trap and Evacuation Flange part #CAM37420. It is not really designed…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 10

Hey David, from previous customers of ours who have the same 2020 Keystone Raptor 424 we have determined that your pin box style is the Lippert 1621 which means for a Gen-Y gooseneck adapter you'd want the #GY58GR that you referenced.

view full answer...

Answer 11

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Installation of Lippert Stabilizer Trailer Jack # LC298707

Product Page this Question was Asked From

Continue Researching