Replacement Seal for Trailer Hub with Bearings L68149 and L44649

Question

Question:

2007 Trails West - Adventure - Bumper Pull BP - 2 horse trailer The double lip bearing seal with a broken/bent spring removed had the following nomenclature on the seal. A 9501 TB 1.720 ID 2.561 OD 0.500 width Trying to find replacement seal with those dimensions? The wheel bearings were L68149 and L44649 Thanks in advance

asked by: Bob L

0

Expert Reply:

For your seal dimensions that you listed the replacement seal part # RG06-050 that you mentioned.

expert reply by: Jameson C

0

Answer 1

The Dexter bearing kit part number K71-717-00 that you referenced is the bearing kit for a number 84 spindle. Our part number for that bearing kit is #BK2-100.

view full answer...

Answer 2

Grease Seal #RG06-050 is the replacement part for the Dexter 010-019-00. It is 1.719 inches inner diameter and 2.565 inches outer diameter. It is a fit for 3500 lb axles. This is a confirmed replacement cross-reference.

view full answer...

Answer 3

We do have a replacement for Nationals part number 473336. It is our Grease Seal - Double Lip #RG06-050. It comes in a two pack. It has an inner diameter of 1.719 inches and an outer diameter of 2.565 inches. I have a review video down below of the…

view full answer...

Answer 4

Tru-Ryde double-lip grease seal kit #RG06-050 will work as a replacement for Hayes seal 09103305 or Al-Ko seal 568861 since these parts all share the same inner diameter of 1.719-inches and the same outer diameter of 2.565-inches. Part #RG06-050 is…

view full answer...

Answer 5

I spoke to my contact at Fulton and he informed me that the Fulton Magnum series jacks were an older line of jacks that had capacities of over 1,000 lbs. Without knowing what capacity your jack is or what model it is it would be hard to pick out…

view full answer...

Answer 6

There are several different Fulton jacks that use a sidewind handle like part #F0933305S00, so to make sure we get you the correct parts, I will need a little more information about your jack. Do you know the model number of your jack? Fulton will…

view full answer...

Answer 7

I have a 5 inch roller, but the largest Bow Roller Assembly that we offer is a 4 inch, like part #YR450Y-400Y. The CE Smith Deep V Keel Roller Assembly #CE10401G is 5 inches and will accomplish the same task that a bow roller will. The only…

view full answer...

Answer 8

Yes, the Replacement Sidewind Handle Kit for Pro Series or Fulton Marine Jacks part #F0933305S00 is exactly what you need for the 1,000 lb Pro Series Swivel Jack like part #PSEJ10000101.

view full answer...

Answer 9

I like the non-marking rollers like the 4 inch bow roller part #TR450B-400B which fits a 1/2 inch shaft or the #YR300B-325B which is 3 inch wide and fits a 1/2 inch shaft. These two are the standard sizes commonly found so I'd measure what you…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

You can verify that the 10-19 grease seal included in Bearing Kit #BK2-100 is the correct one for your spindles by taking two measurements. First you want to measure the rear hub bore where the seal is inserted. The seal's outer diameter needs to…

view full answer...

Replacement Seal for Trailer Hub with Bearings L68149 and L44649

Product Page this Question was Asked From

Continue Researching