Timbren Kit for 1994 Ford F-350 Towing Fifth Wheel Trailer

Question

Question:

1994 F350 crew cab 5.8 single wheel base. 16k 5th wheel hitch. Is your TFR350SDF a good fit for a little more leveling support with 8000# 5th wheel? No interferance with in bed hitch rails? thanks,

asked by: Glen D

0

Expert Reply:

Yes the Timbren kit part # TFR350SDF is a confirmed fit for your 1994 Ford F-350 and would do a great job providing additional support for the rear suspension when towing a 5th wheel trailer.

expert reply by: Jameson C

0

Answer 1

I recommend part #TFR350SDE between the two. This is a direct fit for your vehicle. Part #TFR350SDF is designed for the cab and chassis variants only, and will work if you have this variant with a standard truck bed equipped (This is uncommon).…

view full answer...

Answer 2

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 3

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion…

view full answer...

Answer 4

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from…

view full answer...

Answer 5

If you are considering Timbrens like the #TDR1500DQ and the SumoSprings like the #SSR-307-47 for your 2022 Ram 1500 4x4, I recommend the SumoSprings #SSR-307-47. The SumoSprings will offer the same quality as the Timbrens in terms of suspension…

view full answer...

Answer 6

I recommend going with the Air Lift LoadLifter 7500 XL Ultimate Air Helper Springs #AL89DQ for hauling around an in-bed camper with your 2024 Ford F-350 Super Duty. I really like this kit because it has the higher 7,500 lb rating (which you…

view full answer...

Answer 7

We have the following Gen-Y shock absorbing 5th wheel pin boxes which are compatible with the Lippert Rhino pin box bolt pattern. The weights listed below are the maximum capacities the pin box is capable of supporting. 21,000 lbs - 3.5K TW #GY86GR…

view full answer...

Answer 8

The head alone for the B&W Companion hitch #BWRVK3500 weighs about 70 pounds. Everything else weighs about 130 pounds. So the total weight of the hitch is approximately 200 pounds.

view full answer...

Answer 9

You can replace the Lippert Rhino pin box on your Brinkley 5th wheel. The right one though is going to depend on the pin weight of your trailer. Here are the options that will work to replace the Lippert Rhino: - Pin Weight of 1,500 lbs - 3,500…

view full answer...

Answer 10

I spoke with my contact at Trailair and from your serial number we were able to determine that your trailer came with a 1621 HD pin box which is a long pin box style. I was unable to obtain the exact part number for your Trailair pin box but from…

view full answer...

Answer 11

If you take a look at the linked diagram you can see the minimum recommended clearance distances between truck and trailer for 5th wheel towing. It is recommended to have at least 5-inches from the top of the bed rails to the bottom of the trailer…

view full answer...

Answer 12

A wedge is needed, yes, and the Lippert Turning Point pin box does come with a universal wedge, but it is not a very good fit with the B&W Companion #BWRVK3710. So I highly recommend instead using the 5th Airborne Custom Wedge for B&W Fifth…

view full answer...

Timbren Kit for 1994 Ford F-350 Towing Fifth Wheel Trailer

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching