What Size Bolts are Used to Install Draw Tite Hitch on 2018 Nissan Murano

Question

Question:

Can you tell me what the screw size is for mounting the draw-tite hitch, for a 2018 Nissan Murano?

asked by: Theodore S

0

Expert Reply:

The Draw Tite hitch part # 75952 that fits your 2018 Nissan Murano uses install bolts that are sized M12x1.25x40.

For new hardware we do have hitch hardware replacement with part # RHK.

expert reply by: Jameson C

0

Answer 1

For your 2019 Nissan Murano we only have hitches like the etrailer part #e98907 which have the crosstube underneath the vehicle. Based on the muffler location on your vehicle there just isn't a way to fit a hitch that only has the opening…

view full answer...

Answer 2

The ideal height will actually have to do with how tall the coupler of the trailer is from the ground. The Draw-Tite #76020 will sit at 13 1/2 inches from the ground to the top of the hitch when installed on a 2016 Mazda CX-9. From what I could…

view full answer...

Answer 3

This question actually comes up quite a bit. The hitch receiver tube and safety chain plate will block the sensors located under the rear bumper in the center. However, the sensors further to the right or left will still function and allow you to…

view full answer...

Answer 4

A trailer hitch from a 2013 Nissan Murano won't fit a 2020 Nissan Murano as the vehicle underwent a generation change in 2014, so the spacing and frames are different, necessitating different hitches. The hitch I recommend for your 2020…

view full answer...

Answer 5

In my opinion you are going in the right direction with a frame mounted receiver. The only advantage to a weld on application is that, if welded properly, the attachment point, weld, will be stronger than the hitch or trailer frame steel and one of…

view full answer...

Answer 6

The Curt Trailer Hitch Receiver - Custom Fit - Class III - 2" #C13126 you purchased for your 2016 Nissan Pathfinder is not a fit for a 2018 Murano. That hitch is only a fit for 2013 - 2013 Infiniti JX35, 2013 - 2016 Nissan Pathfinder, and 2014 -…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

We have just what you need. If you type RHK in the search box on our website it will take you to the replacement hardware kit product page. You will then simply type the number of the hitch you need hardware for in the box that is labeled Hitch Item…

view full answer...

Answer 9

The Tow Ready wiring harness #118571 is rated for 7.5 amps for brake lights and turn signals and 7.5 amps total for running lights. The fuse that goes on the power wire connection to the battery is a 10 amp fuse. The wire gauge of the long 12 volt…

view full answer...

Answer 10

If one of the weld nuts on your vehicle is stripped then your only option to install the Curt Class I Trailer Hitch #C11265 is really to obtain a screw tap from a local hardware store so that you can make the weld nut accept a slightly larger bolt.…

view full answer...

Answer 11

If you want to install the Curt Trailer Hitch Receiver - Custom Fit - Class III - 2" #C13182 on your 2016 Jeep Grand Cherokee, you will use M14 bolts that are grade 5 as well as compatible flat washers. That is the replacement for what is…

view full answer...

Answer 12

Apparently, on the 2014 Chrysler Town and Country, on the passenger side frame rail there is a bolt that is holding on the bumper and it should not or cannot be removed. Otherwise there would likely be 6 bolts instead of 5 holding on Curt trailer…

view full answer...