Can 3rd Brake Light Logic Module # PP20-702 be Wired to Trailer Wiring of 2019 Ford F-150

Question

Question:

I have a 2019 F150 and want to know if I can hook up your 3 brake light module PP20-702 to my 4 pin trailer connector for my soft topper.

asked by: Wayson H

0

Expert Reply:

Yes you could use the 3rd Brake Light Logic Module # PP20-702 by wiring it to the trailer light circuits of your 2019 Ford F-150. This will give you the dedicated stoplight circuit you are looking for.

expert reply by: Jameson C

0

Answer 1

The logic box that you are asking about is our Pacer Performance 3rd Brake Light Logic Module #PP20-702. This is a piece of equipment that is required when using an LED light as a 3rd brake light. If there is a specific light style that you are…

view full answer...

Answer 2

You can use a 7-Way and 4-Way connector at the same time just as long as you are not overloading the light circuits. If your camper has a lot of outside lights like running lights, and brake/stop/turn lights then the lights that perform the same…

view full answer...

Answer 3

Yes we do have a logic module that will work to wire your third brake light on your camper shell, part #PP20-702 the Pacer Performance 3rd Brake Light Logic Module. The logic module filters out the unwanted turn signal inputs. This prevents the…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 11

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 12

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Can 3rd Brake Light Logic Module # PP20-702 be Wired to Trailer Wiring of 2019 Ford F-150

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching