How To Find Correct Replacement Suction Cup Mount for Furrion Backup Camera System

Question

Question:

What does the ball Joint on part #LC776462 measure in width? Replacement Suction Cup Mount for Furrion Vision S Wireless RV Backup Camera System.

asked by: Bob

0

Expert Reply:

I don't have specific measurements on the ball for the replacement suction cup mounts but what I can tell you is that the correct one for the Furrion 4.3" monitor is part # LC776462 and the correct one for the Furrion 5" and 7" monitors is part # FR79SR.

expert reply by: Conner L

0

Answer 1

The diameter of the Replacement Suction Cup Mount for Furrion Vision S Wireless RV Backup Camera System #LC776462 is 0.60 inches; I used a digital caliper in order to measure this for you. This mount is a replacement for the Furrion Vision S Wireless…

view full answer...

Answer 2

To remove the base you'll need to pull the cup mount and monitor in opposite directions until the ball joint pops out of place. Since the ball is broken off in the mount you will need to try and take it out using a pair of pliers. To attach the…

view full answer...

Answer 3

The ball size on the suction cup mounts for the Furrion monitors are different sizes, part #LC776462 is for the 4.3" monitor and part #FR79SR is for the 5" and 7" monitors.

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Since your trailer has the bracket #FRCBRKT-BL that would mean your trailer has the Furrion pre-wiring which is very common for newer RVs. The part #FOS43TASF is a fit for this and would be a really easy install. This gives you a monitor with a 4.3…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 8

The Furrion camera system we have is a closed system and would not be compatible with the in-dash display so you would need to purchase GM's camera system to be able to connect to your display instead of having another monitor. If you do end up…

view full answer...

Answer 9

Demco actually has a kit that was designed to convert an Air Force One kit to a Stay in Play DUO which is what you would need since you have hydraulic brakes with the part #SM99231. This will work with what you have now and work great. If you send me…

view full answer...

Answer 10

You can have more than one iPhone "connected" to the Lippert Tire Linc system part #LC37VR but only one can be used at a time. So basically you or your wife could have their phone connected but if you needed to switch between the two phones…

view full answer...

Answer 11

The newer Chevrolet and GM pickup trucks have a known power deficiency issue with the Furrion Vision S Wireless RV Observation Camera System w/ Side Marker Light Cameras #FCE48TASL-05. There is likely nothing wrong that you did, the problem is the…

view full answer...

Answer 12

We have 2 different remotes available for HappiJac electric camper jack systems. - Replacement Remote Control for HappiJac Electric Camper Jack Systems #LC723915 - Replacement Remote Controller for Wireless HappiJac Electric Truck Camper Jacks…

view full answer...