Camera for Vehicle Stereo that Uses RCA for Camera Connections

Question

Question:

Can I plug this into to a aftermarket radio I’m buying and use that as a monitor

asked by: Paul S

0

Expert Reply:

The camera of the # HM50002 does not use a standard connector to attach to an aftermarket stereo so it wouldn't work for you.

expert reply by: Jameson C

0

Paul S.

11/4/2020

Can I plug this into to a aftermarket radio I’m buying and use that as a monitor

Reply

Jameson C.

11/4/2020

The RVS camera part # RVS-777 would work great. It uses RCA connectors like your monitor most likely has and has nightvision so it would work really well.

Reply

Answer 1

The Rear View Safety Backup Camera #RVS-MV1 was designed more for vehicles like cars, not motorhomes. As such it is designed to be installed on and under-hang which orientates the camera differently than it would be on the back of a motorhome.…

view full answer...

Answer 2

The Rear View Safety Backup Camera System #RVS-062710 is a pretty much closed system with each component having a connector to connect to the wiring instead of splicing. Most likely the camera that isn't working has a loose connection so…

view full answer...

Answer 3

I recommend using a direct receiver type of tow bar over a ball mount tow bar when flat towing. You can experiene a lot of rattling with a ball mount style tow bar #RM-501 and would have to have the ball mount tow bar exactly level. With a receiver…

view full answer...

Answer 4

To have the back-up camera on and switch to the side cameras when you use your turn signals using the Rear View Safety Backup Camera System #RVS-062710, you will want to wire the back-up camera to the running lights and then run the side cameras to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

The first thing you will need for your 1999 D250 is a 4-way. The Curt T-Connector Vehicle Wiring Harness #C55317 plugs into the connection points behind your rear bumper and will allow you to power your trailer's signal lights. Once the 4-way is…

view full answer...

Answer 10

Sure thing, I will go ahead and list out what you need for your 2023 Kia Sportage to add a 7-way for a brake controller so you can tow with the Curt Trailer Hitch Receiver #C94WR: - T-Connector Vehicle Wiring Harness with 4-Way Flat Trailer Connector…

view full answer...

Answer 11

When it comes to choosing between the Blue Ox Patriot #BLU37TR and the Brake Buddy Select 3 #HM39524, these systems are extremely similar in their setup and functionality. Both of these systems provide proportional braking in a compact and easy to…

view full answer...

Answer 12

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...