Replacement Control Module for Lippert Ground Control System that Errors Out

Question

Question:

My control panel was blank but I could control the system manually, just no autolevel or display. I replaced the control panel and now the display is working. The autolevel is not however. It stars out working fine but about 30 seconds into the autolevel the entire system just shuts off. When I turn it back on I have a LF jack error and have to re-home in order to clear it. Clears fine but when I try again to autolevel the system just turns off as previously mentioned. I have checked wiring and am getting a consistent 12v to the control module. I believe the control module is bad but want to verify before I shell out $500. Thanks,

asked by: Jason C

0

Expert Reply:

If you are absolutely sure your battery is in great shape and all of the wiring is good the module would be at fault and it would be time to replace it with the part # LC304136 that you referenced.

expert reply by: Jameson C

0

Answer 1

I spoke with my contact at Lippert and he informed me that the lights flashing indicate the low point of the coach and that if you perform a zero point calibration you will correct that. In the service manual you will need to follow the instructions…

view full answer...

Answer 2

It actually is just that, an antenna. I spoke with my contact at Lippert who said that some models of the Lippert Ground Control 3.0 #LC358590 are wireless. The antenna on the Control Module #LC304136 is there for those systems.

view full answer...

Answer 3

I reached out to my contact at Lippert and they said that it sounds like you just aren't holding the 4 buttons for the reset long enough. It requires 5 seconds, but many people will count to 5 a little too fast and the system won't reset. He…

view full answer...

Answer 4

The blank screen on your LCI Ground Control 3.0 could be either a power issue or a control module issue. I recommend first remove the panel and unplug it from the back leaving it unplugged for at least 15 minutes so that it loses all of the residual…

view full answer...

Answer 5

There are a couple different things to consider. With the Lippert 3.0 Ground Control system on your 2018 Grand Design 311BHS, I confirmed with my tech at Lippert that the voltage test should only be on the battery itself. The healthy battery voltage…

view full answer...

Answer 6

We do indeed have the correct replacement for the 694656 control module; I checked with Lippert and you're right that there is a different part number that has taken its place, but is the correct replacement for your Ground Control 3.0 4-point…

view full answer...

Answer 7

The ability of the #RM-2460-2580 Roadmaster Comfort Ride Leaf Spring Suspension Kit to fit without modifications will depend on the existing suspension. This isn't a RV-specific item, the system would be a direct replacement if the RV has…

view full answer...

Answer 8

First you will need to pull the power to the 6-point Set Lippert Ground Control 3.0 Electric Leveling System #LC675817 for at least 15 minutes in effort to reset. Also ensure what your battery bank has a proper charge before doing because the system…

view full answer...

Answer 9

It sounds like you just need to reset the zero point. In order to do this you will need to follow the steps I have attached for you below and in the photo. If this does not fix your issue then please just let me know and I will see if we have any…

view full answer...

Answer 10

It sounds like you have a control module issue if the Lippert leveling system isn't working consistently with the remote functions. If you can find the control panel for the unit behind it there is the control module part #LC304136. Try…

view full answer...

Answer 11

It sounds like you need to re-calibrate the zero point on your Lippert Ground Control 3.0 #LC304136 system. Below I've listed out the steps you'll need to follow and will allow you to use the auto leveling again. Zero Point Calibration The…

view full answer...

Answer 12

I reached out to my tech contact at Lippert and he said there are a couple things to check. First he said it sounds like the jacks are not retracted all the way up and if you press and hold the front arrow the jacks should extend if there is power…

view full answer...

Replacement Control Module for Lippert Ground Control System that Errors Out

Product Page this Question was Asked From

Continue Researching