Reese Fifth Wheel Brackets that Fit 2004 Ford F-250 Long Bed

Question

Question:

Do this brackets fit 2004 heavy duty F250 8 foot bed

asked by: Robert R

0

Expert Reply:

We have a set of fifth wheel brackets that fit your 2004 Ford F-250 long bed with the kit part # RP50082 but the # RP56016 will not work for you as it was designed for a different truck.

expert reply by: Jameson C

0

Answer 1

The rail kit #DM6014 that you referenced will fit your older Demco 5th wheel hitch if it uses base rails that run side to side. To mount these rails to your 2001 GMC Sierra 2500HD with the 6-1/2' bed you need the Universal Mounting Brackets…

view full answer...

Answer 2

Since you have the older style Demco fifth wheel hitch FWH 24PA you have to use the Demco Older Style Rails part #DM6014. Then for a bracket kit you'd want the part #DM8552011 which is a custom fit bracket kit for your 2015 Chevy Silverado…

view full answer...

Answer 3

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

Great question, Jeff! When the Rota-Flex first came out it renovated what a pin box could do and be, but at this point in time that technology is a little more dated and the Gen-Y Hitch Shock Absorbing 5th Wheel Pin Box #325-GH-8040 is the "new…

view full answer...

Answer 6

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 7

There are a couple of options that'll work great with your Lippert Turning Point Pin Box, however one hitch stands out to me more than others. Take a look at the: -Curt E16 5th Wheel Trailer Hitch - Slide Bar Jaw - 16,000 lbs #C16115 This 5th…

view full answer...

Answer 8

Hey David, from previous customers of ours who have the same 2020 Keystone Raptor 424 we have determined that your pin box style is the Lippert 1621 which means for a Gen-Y gooseneck adapter you'd want the #GY58GR that you referenced.

view full answer...

Answer 9

Most fifth wheel rails are made to the same industry standard dimensions. They aren't all though. If you measure 22 inches on center between the two rails and they look like the rails of the #RP30035 that you referenced they would be the industry…

view full answer...

Answer 10

The recommendation for the 10" diameter lube plate on a B&W Companion 5th Wheel Trailer has come from the manufacturer of the fifth wheel hitch, B&W. The Lube Plate for Reese 5th Wheel Trailer Hitches part #RP83002 will work just fine…

view full answer...

Answer 11

I recommend using a Lube Plate #16721 over covering the Demco Recon 5th Wheel Trailer Hitch #DM8550043 in Grease #L74FR. The lube plate is much cleaner and you will not have to constantly clean off the dirt and apply new grease over time.

view full answer...

Answer 12

The mounting holes in the No-Drill Mount Kit #F2530 don't line up perfectly to mount the Air Command II Xtreme Duty Compressor #F2549, but they are close enough that you can widen the holes a bit to accommodate the compressor and avoid drilling…

view full answer...