Inno Gravity Ski and Snowboard Carrier # INA951

Question

Question:

What is the height of the complete rack? In other words, how nub does it stick up when mounted??

asked by: Petey

0

Expert Reply:

When installed, the tallest point of the INNO # INA951 Gravity Ski and Snowboard Carrier would sit exactly 7 inches above the top of the vehicle crossbars. I've provided a photo showing this dimension.

expert reply by: Mike L

0

click to enlarge

Answer 1

With the height of your truck camper at 7-1/2' tall I recommend using a Inno Kayak Lifter Load Assist #INA453. This will clamp onto your crossbars up to 3-1/2" wide and 1-1/8" tall and fits a crossbar spread of 27-39". Since it is…

view full answer...

Answer 2

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 3

I went ahead and checked, and there actually is not a fit kit available for your 2016 Land Rover LR4 and the Inno Dual Angle Ski and Snowboard Carrier #INTX726, unfortunately. Instead, I recommend checking out the Inno Gravity Ski and Snowboard…

view full answer...

Answer 4

Yes, the Rhino-Rack Ski and Fishing Rod Carrier #RR572 that you referenced does fit the Whispbar crossbars you have. The picture I attached shows the carrier installed on a similar set of aero crossbars.

view full answer...

Answer 5

I did see the review saying they used spacers, though that is the only time we have ever come across this, so I wouldn't say yes, spacers are going to be needed to use the Rhino-Rack system, which is the following part number: - Rhino-Rack Vortex…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

Hey Alec, For your 2016 Ford Fusion I recommend the recommend a roof rack from Inno: Inno Aero Crossbars #INXB138-145 Inno Through Feet for Aero Crossbars #INXS250 Custom Fit Kit for Inno XS200, XS250, and INSU-K5 Roof Rack Feet #INK860 As with any…

view full answer...

Answer 8

Aside from a slight change in the appearance of the crossbar (the WingBar Evo has some boxed edges as opposed to the completely smooth front of the AeroBlade) the biggest differences are the rubber strip on top of the crossbar and the weight…

view full answer...

Answer 9

For a roof rack to be compatible on your 2020 Jeep Wrangler with Sky One-Touch Power Top, it can't be mounted on the top of the roof and it needs to be high enough for the folding roof to clear. What you need are tall gutter-mounted roof racks.…

view full answer...

Answer 10

Yes, your kick sensor for your hands free liftgate will still work after installing a Class III receiver on your 2024 Toyota RAV4 XSE. I have linked an install video near the bottom of the page for our etrailer Trailer Hitch Receiver #e23ZR being…

view full answer...

Answer 11

There is rear suspension enhancement that fits your 2024 Toyota RAV4, which are coil springs from Timbren. The correct part number is the following: - Timbren Suspension Enhancement System - Coil Spring Suspension #T58GR

view full answer...

Answer 12

The best trailer hitch receiver for carrying bikes that fits your 2021 Toyota RAV4 Limited Hybrid is the EcoHitch Hidden Trailer Hitch Receiver #EH97FR. The reason for that is because it has the best ground and bumper clearance for a bike rack…

view full answer...

Inno Gravity Ski and Snowboard Carrier # INA951

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching