Towing Mirrors For A 2018 Ram 2500

Question

Question:

I have a 2018 ram 2500 cumins diesel and I need to tow my trailer but my current mirror fold in and the one that I have seen doesnt fold in. Which one you recommend in my situation?

asked by: George

0

Expert Reply:

If you are looking for a towing mirror for your 2018 Ram 2500 I recommend the CIPA Custom Towing Mirrors - Slip On - Driver Side and Passenger Side Item # CM11400. These are custom fit mirrors and do not restrict any functions of your factory mirror.

expert reply by: Shane H

0

Answer 1

I reached out to CIPA directly and the CIPA Custom Towing Mirrors #CM11400 you were looking at will not fit your 2018 Ram 2500 SLT due to it having different mirrors than other models of the Ram. For your 2018 Ram 2500 SLT there is not a custom fit…

view full answer...

Answer 2

For custom towing mirrors that will fit the chrome power folding mirrors on your 2018 Ram 1500 Laramie we have the K-Source Snap & Zap #KS80710. These snap on over the back of your factory mirror and will not obstruct your puddle lights. They…

view full answer...

Answer 3

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 4

It could be a tow package fuse on the vehicle. Use the owners manual to find the locations of fuses/relays related to the tow package wiring to check them and replace as needed. If the issue is not a fuse or relay then you can test the vehicle side…

view full answer...

Answer 5

Since the issue appears to be on the vehicle side for your 2017 Toyota Tacoma, I recommend first checking the connector itself. Look to see if there is any dirt or corrosion built up inside the connector that may preventing a solid connection with…

view full answer...

Answer 6

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 7

My contact at Yates Rubber advises that a nominal 8-inch keel roller does not measure exactly 8 inches; typically they are slightly smaller than the specified size, much the way a piece of 2 x 4 lumber is not exactly 2-inches by 4-inches. I took…

view full answer...

Answer 8

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Answer 9

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5 inches…

view full answer...

Answer 10

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 11

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Answer 12

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Towing Mirrors For A 2018 Ram 2500

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching