Mounting Hole Dimensions of 400 Watt Go Power Industrial Pure Sine Wave Inverter

Question

Question:

Hi there, This is regarding the above listed part. Is there an chance you have the dimensions of the mounting holes on the base of the inverter.

asked by: Ryley M

1

Helpful Expert Reply:

The mounting holes on the Go Power Industrial Pure Sine Wave Inverter part # 34282693 are 4.6" long x 5.9" wide. I have attached a photo to assist with this.

expert reply by: Conner L

1

click to enlarge

Answer 1

From an outlet point of view the Multi Device Charging Station part #37215095 would work great for you as it has the usb ports and the cigarette lighter port you are wanting. As long as your CPAP doesn't draw more than what this circuit on…

view full answer...

Answer 2

A battery disconnect switch (or circuit breaker) is needed for the 400 Watt Go Power Industrial Pure Sine Wave Inverter - GFCI #34282692, but if you want to be able to use it with a remote you will need to get one of the two remotes that work with…

view full answer...

Answer 3

The best option would be to use the Roadmaster 12-volt Outlet Kit, #RM-9332. This kit is was designed to be used as a way to connect the 12-volt connection on supplemental braking systems used when flat towing a vehicle behind a motor coach. What I…

view full answer...

Answer 4

The Progressive Dynamics Pure Sine Wave Inverter #PD34FR is designed to work with both a 30 AMP RV system or 50 Amp RV system. So regardless of which set up your 2017 Winnebago Minnie Trailer has this unit will work with it. This inverter is also…

view full answer...

Answer 5

You are correct the fuse style of the Installation Kit for Go Power Inverters #342GPDCKIT1 is an ATC and not a Class T.

view full answer...

Answer 6

The correct inverter for your setup is really going to come down to the wattage requirements of the appliances you will be using in your 2008 Freedom Express RV when running off the battery bank. I included a chart that goes over common wattage…

view full answer...

Answer 7

The Go Power Industrial Pure Sine Wave Inverter with Transfer Switch #34279458 has a 1,500 watt capacity so you'll just need to look up how many watts your CPAP machine pulls to determine if the inverter is rated high enough to power it.…

view full answer...

Answer 8

To start I would have a licensed technician check the LP pressure running to your Fogatti RV Tankless Water Heater - Gas - Automatic Pilot - 41,800 Btu - White Item #LSB64FR. It needs to be 11" WC for the unit to properly work. If it is…

view full answer...

Answer 9

I reached out to my contact at firestone to confirm a few things. If the compressor is running, it should be filling the bags. The compressor is either going to build air pressure, or not build pressure. So if it is running when the bags are full, we…

view full answer...

Answer 10

It sounds like you may not have power getting back to the camera. Start the truck. Check the plug on the truck to make sure you have power coming from all the pins except one. One will be ground. Have someone run through the functions on the truck…

view full answer...

Answer 11

Yes, the Ultra-Fab Ultra Scissor Jack #UF48-979006 that you referenced can be used in multiples to level and stabilize a trailer. This jack welds or bolts (with hardware you supply) on to your trailer or RV frame. As long as these jacks' 6,500-lb…

view full answer...

Answer 12

As long as you don't have the factory Air Suspension or the Rebel model you'll want the Firestone Coil-to-Air-Spring Conversion Kit #F2595 for your 2018 Ram 1500. This is an air spring kit that can be adjusted to fit your towing/hauling needs…

view full answer...

Mounting Hole Dimensions of 400 Watt Go Power Industrial Pure Sine Wave Inverter

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching