What Type of Fuse Does Installation Kit for Go Power Inverters # 342GPDCKIT1 Use

Question

Question:

The product description indicates a 60 amp Class T fuse. The fuse holder does not appear to fit what I normally think of as a Class T fuse. It looks more like it holds a typical blade fuse - like an ATC. Id like to have a replacement fuse on hand. What fuse would I specify? thanks

asked by: David

1

Helpful Expert Reply:

You are correct the fuse style of the Installation Kit for Go Power Inverters # 342GPDCKIT1 is an ATC and not a Class T.

expert reply by: Jameson C

1

Answer 1

From an outlet point of view the Multi Device Charging Station part #37215095 would work great for you as it has the usb ports and the cigarette lighter port you are wanting. As long as your CPAP doesn't draw more than what this circuit on your…

view full answer...

Answer 2

A battery disconnect switch (or circuit breaker) is needed for the 400 Watt Go Power Industrial Pure Sine Wave Inverter - GFCI #34282692, but if you want to be able to use it with a remote you will need to get one of the two remotes that work with…

view full answer...

Answer 3

There are two ways to wire up two batteries. One way doubles the volts of the two batteries and the other keeps the same amount of volts. In parallel the voltage stays the same and in series it is doubled. Check out the diagram for more info.

view full answer...

Answer 4

The mounting holes on the Go Power Industrial Pure Sine Wave Inverter part #34282693 are 4.6" long x 5.9" wide. I have attached a photo to assist with this.

view full answer...

Answer 5

The best option would be to use the Roadmaster 12-volt Outlet Kit, #RM-9332. This kit is was designed to be used as a way to connect the 12-volt connection on supplemental braking systems used when flat towing a vehicle behind a motor coach. What I…

view full answer...

Answer 6

The correct inverter for your setup is really going to come down to the wattage requirements of the appliances you will be using in your 2008 Freedom Express RV when running off the battery bank. I included a chart that goes over common wattage…

view full answer...

Answer 7

The Progressive Dynamics Pure Sine Wave Inverter #PD34FR is designed to work with both a 30 AMP RV system or 50 Amp RV system. So regardless of which set up your 2017 Winnebago Minnie Trailer has this unit will work with it. This inverter is also…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

What Type of Fuse Does Installation Kit for Go Power Inverters # 342GPDCKIT1 Use

Product Page this Question was Asked From

Continue Researching