Will Rhino Roof Bar Stops Fit on Thule Square Bars?

Question

Question:

Hi will the rhino roof stops fit the Thule roof bar it’s the square type we have.

asked by: John

0

Expert Reply:

There are some solutions for using load stops with your Thule cross bars, but unfortunately, the Rhino Load Stops are made for use with Rhino Delta Bar Systems and Rhino Modular Racks. Instead I recommend Thule Load Stops # TH503. These are confirmed by Thule to fit any of the Thule square-style roof bars.

expert reply by: John R

0

Answer 1

To replace the load stops on the Thule TracRac for your 2018 Chevy Colorado you need 3 different parts; the Load Stop #8537165, M8 T-Bolt #853-5715, and the Hand Knob #TAKB-90004. Obviously you'll need 2 of each if you need to replace both…

view full answer...

Answer 2

The height of the load stop is 5 inches but it would not be an ideal solution for carrying two kayaks. The simplest solution for carrying two kayaks would be the Stacker part #TH830 which would allow you to secure each of your kayaks on either side…

view full answer...

Answer 3

The Thule Load Stops for Load Bars #TH503 are 3-1/2" tall and will take up 3" of crossbar space each (see attached photo). I confirmed this with my contact at Thule.

view full answer...

Answer 4

The Load Stops for Rhino-Rack Vortex Aero Crossbars #RRRLH2 install by sliding into the T-Slot of the crossbar. For the 53" Thule WingBar Evo Crossbars #TH711420 the load stops will slide between the dual rubber T-Slot strips so you won't…

view full answer...

Answer 5

Technically yes the Thule Load Stops #TH503 will fit around the Rhino-Rack Euro Bar Crossbars, like part #RREB126B, but please note that the Euro bars are slightly smaller than the Thule SquareBars (1-1/4" wide x 7/8" tall), like part…

view full answer...

Answer 6

I have a solution for you, but unfortunately Thule does not offer the load stops as single items, and to replace the Thule load stops, you'll need to purchase part #TH503 which is a four pack. If you're OK with mismatched pairs, Rhino…

view full answer...

Answer 7

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 8

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 10

The Trailer Hub and Drum Assembly part #AKHD-545-35-K is the correct replacement for an AL-KO 7230. In regards to the braking assemblies, I suggest getting a new pair, the Electric Trailer Brake Kit part #AKEBRK-35-SA. This option will save you some…

view full answer...

Answer 11

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 12

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Will Rhino Roof Bar Stops Fit on Thule Square Bars?

Product Page this Question was Asked From

Continue Researching