Replacement Pinion Shaft for Fulton K1550 Used on Boat Lift

Question

Question:

The end of the drive shaft of my k1550 where the boat lift wheel attaches broke off. does this replacement drive shaft work with a boat lift wheel. Fulton Accessories and Parts - F501118

asked by: Bob D

1

Helpful Expert Reply:

Replacement Pinion Shaft for Fulton 1500 Series Winch # F501118 is the correct replacement for your drive shaft. The K1550 is part # F143100 and the shaft is shown in the attached photo where it connects to the handle. The boat lift wheel will attach to this shaft in that same location as it did before.

expert reply by: Jason S

1

click to enlarge

Bob

9/28/2020

The end of the drive shaft of my k1550 where the boat lift wheel attaches broke off. does this replacement drive shaft work with a boat lift wheel. Fulton Accessories and Parts - F501118

Reply

Jason S.

9/28/2020

Unfortunately we have not yet made a video for that particular installation. To remove the old drive shaft and install the Replacement Pinion Shaft for Fulton 1500 Series Winch # F501118 you will simply start from the handle and disassemble your current drive shaft one piece at a time. Once you've removed the handle, two nuts and bushing, then you will go to the opposite side of the shaft and on the inside there is a clip you will remove. That will give you the movement you need to continue disassembly and remove the drive shaft. Installing the new one will use the same process in reverse.

Reply

Answer 1

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 2

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 3

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 4

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 5

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 6

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 7

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 8

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 9

The Trailer Leaf Spring, 2250 lbs. 6 Leaf, item #e27SR, is sold as a replacement spring for older trailers and measures 26 inches for eye to eye, center to center. If you are replacing the springs and hangers you will need to use the same center to…

view full answer...

Answer 10

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 11

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 12

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Replacement Pinion Shaft for Fulton K1550 Used on Boat Lift

Products Referenced in This Question

Featured Help Information

Miscellaneous Media

Continue Researching