How Do I Select my Preferred Temperature on the Furrion RV Electric Fireplace with Logs

Question

Question:

I have the 40 inch fireplace all I have for temperature settings are low high and off how do I put an auto where I can a specific temperature like 70°?

asked by: Matt H

1

Helpful Expert Reply:

To adjust the temperature setting on your Furrion RV Electric Fireplace with Logs part # FF40SW15ABL you hold down the button that controls the high, low and off for 5 seconds. This will allow you to choose temperatures between 65 and 90 at 5 degree increments.

Check out the linked video. At the 2:30 mark it shows exactly how to do this.

expert reply by: Randy B

1

Answer 1

No, the Rear View Safety Extendable Monitor Mount #RVS-1419 is only compatible with their own brand of camera system monitors. Furrion uses a ball connector #LC776462 and makes it a different size than other brands so that you have to use only…

view full answer...

Answer 2

The Rear View Safety Extendable Monitor Mount #RVS-1419 will fit with any of the RVS monitors that are a monitor only. From my understanding the monitors that are built into the rearview mirror have the standard rearview mirror mount to that would…

view full answer...

Answer 3

To remove your Furrion RV Electric Fireplace with Crystals - 30" Wide #FF30SC15ABL from the wall you will need to lift the glass and pull it towards you to remove it from the fireplace. You'll then find 4 larger sized square openings…

view full answer...

Answer 4

Since you've already replaced the factory fireplace with the Furrion RV Electric Fireplace with Crystals #FF30SC15ABL and are still facing the same exact issue it leads me to believe the issue is with the outlet/wiring. You could be getting…

view full answer...

Answer 5

It probably is an issue with the circuit board which unfortunately is not replaceable. In those situations the only real solution is a new fireplace like the #FF30SC15ABL that you referenced.

view full answer...

Answer 6

If you checked the outlet with a multimeter #PT89ZR and are getting power to the outlet and the #FF30SC15ABL still won't power on then the control board is most likely fried and would need to be replaced. You can try reaching out to Furrion…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion…

view full answer...

Answer 9

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

I spoke with my contact at Trailair and from your serial number we were able to determine that your trailer came with a 1621 HD pin box which is a long pin box style. I was unable to obtain the exact part number for your Trailair pin box but from…

view full answer...

Answer 12

Hey Jay. It sounds like you are on the right track here because a sidewinder pin box will be your only option for pulling your 5th wheel since you have a short bed truck with the Rambox. That said, you are right that the Reese Sidewinder cannot be…

view full answer...