Are the HappiJac Original Turnbuckles Spring Loaded or Rubber Cushioned

Question

Question:

Is this a spring type or rubber cushion?

asked by: Karl H

0

Expert Reply:

The Replacement Front Turnbuckle for HappiJac Original Turnbuckle Set # LC182901 is a spring loaded turnbuckle.

expert reply by: Erik B

0

Answer 1

The Furrion AC/DC Distribution Panel #FDP12WABL does cover everything you'd need on the output side based on the circuits you are wanting to run in your travel trailer. It can only accept AC power on the input side like you mentioned so you would…

view full answer...

Answer 2

Assuming the tie down locations of your flat bed truck are built strong enough there's no reason you couldn't use turnbuckles like the Happijac Original Turnbuckles part #LC182901 that you referenced. Or for the spring loaded version the part…

view full answer...

Answer 3

The main difference between the Torklift Locking FastGun Turnbuckles, #TLS9522-2-LK, and the AnchorGuard Derringer Turnbuckles, #TLS9020, is how the camper tie-downs are mounted on your truck. The FastGun #TLS9522-2-LK are designed to be used with…

view full answer...

Answer 4

To maintain the warranty of the Torklift Custom Frame-Mounted Camper Tie-Downs, #TLN2409 and #TLR3500, for your 2010 Nissan Frontier, you will want 4 spring loaded turnbuckles like the Torklift SpringLoad XL Turnbuckles, #TLS9050A or the FastGun…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 8

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

I definitely understand being a bit overwhelmed by the amount of options in front of you, however I can definitely help with differentiating the trailer hitches for your 2019 Subaru Outback Wagon along with explaining my personal recommendation,…

view full answer...

Are the HappiJac Original Turnbuckles Spring Loaded or Rubber Cushioned

Product Page this Question was Asked From

Continue Researching