Can I Use the Timbren GMRCK25D On a 2019 GMC Sierra 2500HD

Question

Question:

I have a 3.5 in. lift on my truck . The rear plate is approx.: 1 inch. on the rear axle. Will the 25s work?

asked by: Art S

0

Expert Reply:

Yes. The Timbren SES # TGMRCK25D can be used on trucks that are lifted like your 2019 GMC Sierra 2500. You will want to have approximately 1" between the bottom of the spring and the axle when installed, but if you get them installed and there is more than that you can use the Timbren 1" Spacer For Raised Frame Vehicles - 3/8" Bushing # A25723-90AH00 to close that gap.

expert reply by: Erik B

0

Answer 1

Timbren does have spacers, #A25723-90AH00, that you could use. You would need a total of 4 of them since each is 1 inch tall and because you have a 2 inch lift. I have included a couple of video links for you. One is an installation of kit…

view full answer...

Answer 2

When we have installed the spacers like the part #TA25722-90P00 with a Timbren like part #TGMRCK25D on a lifted truck we had to go to a local hardware store to track down a longer nut and bolt. Check out the install video that shows a similar install…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 11

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 12

You can use the RV Propane Gas Detector #RS64FR to replace your current Atwood 31013 propane gas detector. This will also use a 12v, 2-wire installation like your current detector.

view full answer...