Recommended Center Cap for Westlake LH36FR ST225/75R15 Tire w/ 15 Liger Aluminum Wheel

Question

Question:

Hello i have purchased a set of the LH36FR Westlake ST225/75R15 Radial Tire w/ 15inch Series Liger Aluminum Wheel - 6 on 5-1/2 - LR E - Glossy Black I am looking for a hub cab that is compatible with this wheel. Thanks

asked by: Anthony W

0

Expert Reply:

I believe you're looking for a center cap, is that correct?

The wheel used on the # LH36FR wheel/tire combo has a 4.25 inch pilot diameter, so you'll need a center cap with a matching diameter. The Taskmaster # CXF104B would match up very well, as it's also black and chrome/silver so it'd match your wheel. The caps are sold in a quantity of 1.

expert reply by: Mike L

0

Answer 1

Fortunately, there is only one common bolt pattern for 6 lug wheels used on trailers which is 6 on 5-1/2". I will attach a link that will help you measure your bolt pattern for future references. For a 6 lug spare tire, I recommend using…

view full answer...

Answer 2

From the picture that you sent in it looks like you have the Lionshead Aluminum Lynx Trailer Wheel. Unfortunately, we no longer carry the lynx wheel. We do have a wheel that looks very similar. It is the Westlake Westlake ST225/75R15 Radial Tire w/…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 5

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 6

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Your math is correct in your trailer weight load example. If a fully-loaded tandem axle trailer weighs 4000-lbs then each of the 4 tires will bear 1/4th of that load, or 1000-lbs. In this case a tire rated for 1300-lbs would provide a good safety…

view full answer...

Answer 10

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 11

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...