Thread Dimensions On A Replacement Threaded Hitch Bolt for SportRack Bike Racks and Cargo Carriers

Question

Question:

What dimension are the threads on this pin. Are the metric, imperial, NC or NF?

asked by: George R

0

Expert Reply:

The dimensions on the Replacement Threaded Hitch Bolt for SportRack Bike Racks and Cargo Carriers
Item # 05002400000 is 1/2 inch at a -13 course count.

expert reply by: Shane H

0

Answer 1

I spoke with my contact at Sportrack who informed me that their hitch bolt part #05002400000 is 3-1/4 inches in length with a hex head size of 1/2 inch by 13 mm. The diameter is 1/2 inch. The closest hitch bolt we have to what you are looking for…

view full answer...

Answer 2

Yes, the Anti-Rattle Hitch Lock #SR0901 will fit your 20x60 SportRack Vista Cargo Carrier SR9851 with a 2" hitch.

view full answer...

Answer 3

The Replacement Threaded Hitch Bolt #05002400000 you were looking at is 3-5/16" long and is 1/2" x 13 course thread. This bolt is designed for SportRack bike racks and cargo carriers, and is not a confirmed fit for your Swiss Cargo Bike…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 9

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 10

Yes, you can install a Curt Trailer Hitch Receiver #C11433 on your 2019 Chevrolet Spark. This receiver is capable of supporting up to 200lbs of tongue weight. With each of the Lectric 3.0 e-bikes weighing roughly 60lbs without the battery you will…

view full answer...

Answer 11

I recommend the Roadmaster Dual Hitch Receiver Adapter, 10" Drop/Rise item #RM-077-10. This adapter was designed for this type of set up. Your Jeep Rubicon and Swagman E bike rack weigh well below the 10,000 lbs maximum capacity of this hitch. I…

view full answer...

Answer 12

The weight distribution system that has the best sway control and is properly rated for your tongue weight that will be between 450 and 500 lbs is the Reese Strait Line part #RP66083. This would be my first pick as your best option as it has a tongue…

view full answer...

Thread Dimensions On A Replacement Threaded Hitch Bolt for SportRack Bike Racks and Cargo Carriers

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching