Correct Triple SolidStep for 24-7/8 Inch Door Width

Question

Question:

my door width itself is 24 7/8inch , inside door flange to flange is 24 1/8inch , opening between sides of door jamb is25 5/16inch From what im reading from other questions I might be able to use # LC791572 but then I seen #LC698799 that says fits a 24inch door. which one is the correct one to order ? thanks

asked by: Carl

0

Expert Reply:

The correct triple SolidStep will be determined by measuring your door width from frame to frame and rounding up to the nearest even number.

So for a door width of 24-7/8 inches, you were correct in your initial assessment; the steps you need are the SolidStep Manual Fold-Down Steps # LC791572.

I have added a link to a video review and install for you to check out as well.

expert reply by: Kyle S

0

Answer 1

I am happy to recommend a SolidStep option for the 2019 heartland pioneer re275. However, I would need a couple of measurements from you first to get you the correct step. First measure the door way width frame to frame like in the photo I have…

view full answer...

Answer 2

Based on all the dimensions you listed the Lippert SolidStep part #LC791572 that you referenced will fit and work well. In the attached picture you can see that it does not take up much space when stored vertically. So if you have 14-3/4 inches of…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 5

The SolidStep Manual Fold-Down Steps part #LC791572 will fit a door way from 25" -28.9" wide when measuring the frame inside. If the factory label sticker shows a doorway width between 26"-29" then the above steps will work for…

view full answer...

Answer 6

In terms of choosing a Lippert Solid Step, you'll use the width of the finished door at it's narrowest. Round that number up to the next full inch, which in your case would be 28 inches. In that case, you'll want the adjustable model…

view full answer...

Answer 7

Yes, the #TLD2142 is exactly what you need for your 2019 Ram 3500 with running boards extending under the truck bed. For the rear, you need the #TLD3112 if you have the factory hitch or #TLR3510 if you have the TorkLift SuperHitch Magnum 30K.

view full answer...

Answer 8

We've seen this issue before on an older camper that had the screen door installed a little lower than how they are now. An installer here actually had this exact problem. If your door is close to closing, a couple suggestions that you can try…

view full answer...

Answer 9

Hey Joe, yes the Lippert stabilizer jack part #LC298707 does fit your Grand Design Transcend 245RL but it is sold individually so if you wanted a set for the front and the rear you would need to order a quantity of two.

view full answer...

Answer 10

The MORryde StepAbove RV Steps #MR85RR weighs about 70 lbs. As far as the flip step, I assume you are referring to the MORryde Flip Tread RV Steps #MR42UR which weighs about 45 lbs. Both of these steps will fit your 28" wide door. Personally I…

view full answer...

Answer 11

I recommend Advent Air RV Air Conditioner part #ACM135C for the 8.5x24 ft enclosed trailer. The temperature range is 65 degrees F to 90 degrees F so it will keep your enclosed trailer nice and cool on hot days. You can also add a heat strip with part…

view full answer...