Weight Difference Between Aluminum and Steel Torklift Tie Downs

Question

Question:

What are the weight differences between the TLF2012 and TLF2012A and also the TLF3004 and TLF3004A? I need to extend my 2inch class 3 hitch 22inch to 24inch to clear my camper. I want it to carry a bike rack with no more than 200lbs total weight. I notice that 18inch is the longest extension made. I understand that stability is a bigger issue than tongue weight. Can I use two extensions with hitch stabilizers and maybe even some side-to-side stabilizing straps? Short of replacing the hitch itself what, if anything, would you recommend? Thank you

asked by: Mark D

0

Expert Reply:

The part # TLF2012A weighs 27 lbs and the # TLF2012 weighs 31 lbs. The # TLF3004A weighs 35 lbs and the # TLF3004 weighs 28 lbs.

I would not recommend using two hitch extenders with a bike rack. You might consider a front hitch to carry a bike rack.

expert reply by: Jameson C

0

Answer 1

The Solera Gas Strut part #LC280343 is designed for Lippert-Solera branded awnings. That said, it should be able to be used with others but you'd need to verify the dimensions in order to ensure compatibility. The length for this strut will…

view full answer...

Answer 2

The correct replacement for your Power Gear 522176 is #LC383745.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better option…

view full answer...

Answer 8

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

To replace your NOK AD2527E seal you can use #168233. It has an inner diameter of 1.688 inches and an outer diameter of 2.332 inches. Based on what I could find on the NOK AD2527E the inner diameter is the same and the outer diameter is 2.328 inches.…

view full answer...

Answer 12

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...