HappiJac Truck-Mounted Camper Tie-Downs for 1999 Ford F-350 With Long Bed and Factory Hitch

Question

Question:

Looking for the correct kit tie downs for a truck and slide in camper. Truck 1999 Ford Super duty F350 dual wheels 8 foot bed 7.3 power stroke engine 2 wheel drive anymore questions, just ask.

asked by: Al Y

1

Helpful Expert Reply:

The correct HappiJac tie-downs for your 1999 Ford F-350 with an 8 foot bed and a factory-installed trailer hitch receiver are the following:

- HappiJac Truck-Mounted Camper Tie-Downs # LC182910-182971

Then for turnbuckles you will need the compatible HappiJac Original Turnbuckles for Camper Tie-Downs # LC182898.

I have added links to instructions and video reviews for you to check out as well.

expert reply by: Kyle S

1

Answer 1

As we do not carry the Atwood jacks, I cannot confirm the fitment without knowing the measurements. However, the bolt holes on the HappiJac Swing Out Extension Brackets #LC182496 will measure 7-1/4" between all the bolt holes, picture included.…

view full answer...

Answer 2

The best camper tie-downs and turnbuckles for your 2004 Ford F-350 with an 8 foot bed are from TorkLift because they offer the best strength and stability due to bolting directly to your truck's frame. The correct fit for the front tie-downs is…

view full answer...

Answer 3

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The Hellwig Adjustable Big Wig Rear Anti-Sway Bar #HE94FR is only going to leave a few inches between it and the spare tire, as you can see in the attached picture. Depending on how far forward you have the tire it could potentially interfere with…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

We have run into this quite a few times in the past, and the best option will be replacing the Lance 7-pin connector with a standard 7-way blade connector like the #PK12706. This will give you a standard 7-way connector to plug into the factory 7-way…

view full answer...

Answer 10

You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better option…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...